ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board

	sun7i-a20-olinuxino-lime.dtb \

	sun7i-a20-olinuxino-lime2.dtb \

	sun7i-a20-olinuxino-micro.dtb \

	sun7i-a20-pcduino3.dtb

	sun7i-a20-pcduino3.dtb \

	sun7i-a20-pcduino3-nano.dtb

dtb-$(CONFIG_MACH_SUN8I) += \

	sun8i-a23-ippo-q8h-v5.dtb \

	sun8i-a23-ippo-q8h-v1.2.dtb

/*

 * Copyright 2015 Adam Sampson <ats@offog.org>

 *

 * This file is dual-licensed: you can use it either under the terms

 * of the GPL or the X11 license, at your option. Note that this dual

 * licensing only applies to this file, and not this project as a

 * whole.

 *

 *  a) This file is free software; you can redistribute it and/or

 *     modify it under the terms of the GNU General Public License as

 *     published by the Free Software Foundation; either version 2 of the

 *     License, or (at your option) any later version.

 *

 *     This file is distributed in the hope that it will be useful,

 *     but WITHOUT ANY WARRANTY; without even the implied warranty of

 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 *     GNU General Public License for more details.

 *

 *     You should have received a copy of the GNU General Public

 *     License along with this file; if not, write to the Free

 *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,

 *     MA 02110-1301 USA

 *

 * Or, alternatively,

 *

 *  b) Permission is hereby granted, free of charge, to any person

 *     obtaining a copy of this software and associated documentation

 *     files (the "Software"), to deal in the Software without

 *     restriction, including without limitation the rights to use,

 *     copy, modify, merge, publish, distribute, sublicense, and/or

 *     sell copies of the Software, and to permit persons to whom the

 *     Software is furnished to do so, subject to the following

 *     conditions:

 *

 *     The above copyright notice and this permission notice shall be

 *     included in all copies or substantial portions of the Software.

 *

 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES

 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT

 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR

 *     OTHER DEALINGS IN THE SOFTWARE.

 */

/dts-v1/;

#include "sun7i-a20.dtsi"

#include "sunxi-common-regulators.dtsi"

#include <dt-bindings/gpio/gpio.h>

#include <dt-bindings/interrupt-controller/arm-gic.h>

/ {

	model = "LinkSprite pcDuino3 Nano";

	compatible = "linksprite,pcduino3-nano", "allwinner,sun7i-a20";

	leds {

		compatible = "gpio-leds";

		pinctrl-names = "default";

		pinctrl-0 = <&led_pins_pcduino3_nano>;

		/* Marked "LED3" on the PCB. */

		usr1 {

			label = "pcduino3-nano:green:usr1";

			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; /* PH16 */

		};

		/* Marked "LED4" on the PCB. */

		usr2 {

			label = "pcduino3-nano:green:usr2";

			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; /* PH15 */

		};

	};

};

&ahci {

	target-supply = <&reg_ahci_5v>;

	status = "okay";

};

&ehci0 {

	status = "okay";

};

&ehci1 {

	status = "okay";

};

&gmac {

	pinctrl-names = "default";

	pinctrl-0 = <&gmac_pins_rgmii_a>;

	phy = <&phy1>;

	phy-mode = "rgmii";

	status = "okay";

	phy1: ethernet-phy@1 {

		reg = <1>;

	};

};

&i2c0 {

	pinctrl-names = "default";

	pinctrl-0 = <&i2c0_pins_a>;

	status = "okay";

	axp209: pmic@34 {

		compatible = "x-powers,axp209";

		reg = <0x34>;

		interrupt-parent = <&nmi_intc>;

		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;

		interrupt-controller;

		#interrupt-cells = <1>;

	};

};

&ir0 {

	pinctrl-names = "default";

	pinctrl-0 = <&ir0_pins_a>;

	status = "okay";

};

&mmc0 {

	pinctrl-names = "default";

	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;

	vmmc-supply = <&reg_vcc3v3>;

	bus-width = <4>;

	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */

	cd-inverted;

	status = "okay";

};

&ohci0 {

	status = "okay";

};

&ohci1 {

	status = "okay";

};

&pio {

	ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 {

		allwinner,pins = "PH2";

		allwinner,function = "gpio_out";

		allwinner,drive = <SUN4I_PINCTRL_10_MA>;

		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;

	};

	led_pins_pcduino3_nano: led_pins@0 {

		allwinner,pins = "PH16", "PH15";

		allwinner,function = "gpio_out";

		allwinner,drive = <SUN4I_PINCTRL_10_MA>;

		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;

	};

	usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 {

		allwinner,pins = "PH11";

		allwinner,function = "gpio_out";

		allwinner,drive = <SUN4I_PINCTRL_10_MA>;

		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;

	};

};

&reg_ahci_5v {

	pinctrl-0 = <&ahci_pwr_pin_pcduino3_nano>;

	gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */

	status = "okay";

};

&reg_usb1_vbus {

	pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;

	gpio = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */

	status = "okay";

};

&reg_usb2_vbus {

	status = "okay";

};

&uart0 {

	pinctrl-names = "default";

	pinctrl-0 = <&uart0_pins_a>;

	status = "okay";

};

&usbphy {

	usb1_vbus-supply = <&reg_usb1_vbus>;

	usb2_vbus-supply = <&reg_usb2_vbus>;

	status = "okay";

};