Commit fdcad71c authored by Nicolas Ferre's avatar Nicolas Ferre
Browse files

at91: at91sam9g20ek modify dual slot evaluation kit 



at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.

Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.

Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: default avatarAndrew Victor <linux@maxim.org.za>
parent a9366e61

arch/arm/mach-at91/Kconfig

+11 −9
Original line number Diff line number Diff line
@@ -289,13 +289,6 @@ config MACH_NEOCORE926 
	help

	  Select this if you are using the Adeneo Neocore 926 board.



config MACH_AT91SAM9G20EK_2MMC

	bool "Atmel AT91SAM9G20-EK Evaluation Kit modified for 2 MMC Slots"

	depends on ARCH_AT91SAM9G20

	help

	  Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit

	  Rev A or B modified for 2 MMC Slots.



endif



# ----------------------------------------------------------
@@ -322,7 +315,16 @@ config MACH_AT91SAM9G20EK 
	bool "Atmel AT91SAM9G20-EK Evaluation Kit"

	depends on ARCH_AT91SAM9G20

	help

	  Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit.

	  Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit

	  that embeds only one SD/MMC slot.



config MACH_AT91SAM9G20EK_2MMC

	bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots"

	depends on ARCH_AT91SAM9G20

	help

	  Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit

	  with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and

	  onwards.



config MACH_CPU9G20

	bool "Eukrea CPU9G20 board"
@@ -392,7 +394,7 @@ config MTD_AT91_DATAFLASH_CARD 


config MTD_NAND_ATMEL_BUSWIDTH_16

	bool "Enable 16-bit data bus interface to NAND flash"

	depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)

	depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)

	help

	  On AT91SAM926x boards both types of NAND flash can be present

	  (8 and 16 bit data bus width).

arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c

+15 −8
Original line number Diff line number Diff line
@@ -90,7 +90,7 @@ static struct at91_udc_data __initdata ek_udc_data = { 
 * SPI devices.

 */

static struct spi_board_info ek_spi_devices[] = {

#if !defined(CONFIG_MMC_ATMELMCI)

#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91))

	{	/* DataFlash chip */

		.modalias	= "mtd_dataflash",

		.chip_select	= 1,
@@ -113,7 +113,7 @@ static struct spi_board_info ek_spi_devices[] = { 
 * MACB Ethernet device

 */

static struct at91_eth_data __initdata ek_macb_data = {

	.phy_irq_pin	= AT91_PIN_PC12,

	.phy_irq_pin	= AT91_PIN_PB0,

	.is_rmii	= 1,

};
@@ -194,24 +194,27 @@ static void __init ek_add_device_nand(void) 


/*

 * MCI (SD/MMC)

 * det_pin and wp_pin are not connected

 * wp_pin is not connected

 */

#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)

static struct mci_platform_data __initdata ek_mmc_data = {

	.slot[0] = {

		.bus_width	= 4,

		.detect_pin	= -ENODEV,

		.detect_pin	= AT91_PIN_PC2,

		.wp_pin		= -ENODEV,

	},

	.slot[1] = {

		.bus_width	= 4,

		.detect_pin	= -ENODEV,

		.detect_pin	= AT91_PIN_PC9,

		.wp_pin		= -ENODEV,

	},



};

#else

static struct amci_platform_data __initdata ek_mmc_data = {

static struct at91_mmc_data __initdata ek_mmc_data = {

	.slot_b		= 1,	/* Only one slot so use slot B */

	.wire4		= 1,

	.det_pin	= AT91_PIN_PC9,

};

#endif
@@ -221,13 +224,13 @@ static struct amci_platform_data __initdata ek_mmc_data = { 
static struct gpio_led ek_leds[] = {

	{	/* "bottom" led, green, userled1 to be defined */

		.name			= "ds5",

		.gpio			= AT91_PIN_PB12,

		.gpio			= AT91_PIN_PB8,

		.active_low		= 1,

		.default_trigger	= "none",

	},

	{	/* "power" led, yellow */

		.name			= "ds1",

		.gpio			= AT91_PIN_PB13,

		.gpio			= AT91_PIN_PB9,

		.default_trigger	= "heartbeat",

	}

};
@@ -254,7 +257,11 @@ static void __init ek_board_init(void) 
	/* Ethernet */

	at91_add_device_eth(&ek_macb_data);

	/* MMC */

#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)

	at91_add_device_mci(0, &ek_mmc_data);

#else

	at91_add_device_mmc(0, &ek_mmc_data);

#endif

	/* I2C */

	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));

	/* LEDs */

CRA Git | Maintained and supported by SUSTech CRA and CCSE