hwmon: (ds1621) Remove detect function

Supported chips:

  * Dallas Semiconductor / Maxim Integrated DS1621

    Prefix: 'ds1621'

    Addresses scanned: I2C 0x48 - 0x4f

    Addresses scanned: none

    Datasheet: Publicly available from www.maximintegrated.com

  * Dallas Semiconductor DS1625

    Prefix:

     'ds1621' - if binding via _detect function

     'ds1625' - explicit instantiation

    Addresses scanned: I2C 0x48 - 0x4f

    Prefix: 'ds1625'

    Addresses scanned: none

    Datasheet: Publicly available from www.datasheetarchive.com

  * Maxim Integrated DS1631

    Prefix: 'ds1631'

    Addresses scanned: I2C 0x48 - 0x4f

    Addresses scanned: none

    Datasheet: Publicly available from www.maximintegrated.com

  * Maxim Integrated DS1721

    Prefix: 'ds1721'

    Addresses scanned: I2C 0x48 - 0x4f

    Addresses scanned: none

    Datasheet: Publicly available from www.maximintegrated.com

Authors:

but the DS1621 is meant to replace it. The DS1631 and DS1721 are also

pin compatible with the DS1621, but provide multi-resolution support.

Since there is no version register, there is no unique identification

for these devices. In addition, the DS1631 and DS1721 will emulate a

DS1621 device, if not explicitly instantiated (why? because the detect

function compares the temperature register values bits and checks for a

9-bit resolution). Therefore, for correct device identification and

functionality, explicit device instantiation is required.

Since there is no version or vendor identification register, there is

no unique identification for these devices. Therefore, explicit device

instantiation is required for correct device identification and functionality.

And, for correct identification and operation, each device must be

explicitly instantiated, one device per address, in this address

range: 0x48..0x4f.

The DS1721 is pin compatible with the DS1621, has an accuracy of +/- 1.0

degree Celsius over a -10 to +85 degree range, a minimum/maximum alarm

#include <linux/sysfs.h>

#include <linux/kernel.h>

/* Addresses to scan */

static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,

					0x4d, 0x4e, 0x4f, I2C_CLIENT_END };

/* Supported devices */

enum chips { ds1621, ds1625, ds1631, ds1721 };

	.is_visible = ds1621_attribute_visible

};

/* Return 0 if detection is successful, -ENODEV otherwise */

static int ds1621_detect(struct i2c_client *client,

			 struct i2c_board_info *info)

{

	struct i2c_adapter *adapter = client->adapter;

	int conf, temp;

	int i;

	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA

				     | I2C_FUNC_SMBUS_WORD_DATA

				     | I2C_FUNC_SMBUS_WRITE_BYTE))

		return -ENODEV;

	/*

	 * Now, we do the remaining detection. It is lousy.

	 *

	 * The NVB bit should be low if no EEPROM write has been requested

	 * during the latest 10ms, which is highly improbable in our case.

	 */

	conf = i2c_smbus_read_byte_data(client, DS1621_REG_CONF);

	if (conf < 0 || conf & DS1621_REG_CONFIG_NVB)

		return -ENODEV;

	/*

	 * The ds1621 & ds1625 use 9-bit resolution, so the 7 lowest bits

	 * of the temperature should always be 0 (NOTE: The other chips

	 * have multi-resolution support, so if they have 9-bit resolution

	 * configured and the min/max temperature values set accordingly,

	 * then if not explicitly instantiated, they *will* appear as and

	 * emulate a ds1621 device).

	 */

	for (i = 0; i < ARRAY_SIZE(DS1621_REG_TEMP); i++) {

		temp = i2c_smbus_read_word_data(client, DS1621_REG_TEMP[i]);

		if (temp < 0 || (temp & 0x7f00))

			return -ENODEV;

	}

	strlcpy(info->type, "ds1621", I2C_NAME_SIZE);

	return 0;

}

static int ds1621_probe(struct i2c_client *client,

			const struct i2c_device_id *id)

{

	.probe		= ds1621_probe,

	.remove		= ds1621_remove,

	.id_table	= ds1621_id,

	.detect		= ds1621_detect,

	.address_list	= normal_i2c,

};

module_i2c_driver(ds1621_driver);