Commit e555e5b1 authored by Maxime Chevallier's avatar Maxime Chevallier Committed by David S. Miller
Browse files

net: phy: marvell10g: Use 2500BASEX when using 2.5GBASET 



The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.

Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.

At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.

This was tested with :
 - The 88X3310, which is on the MacchiatoBin
 - The 88E2010, an Alaska PHY that has no fiber interfaces, and is
   limited to 5G maximum speed.

Signed-off-by: default avatarMaxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 0feaccd5

drivers/net/phy/marvell10g.c

+19 −7
Original line number Diff line number Diff line
@@ -235,6 +235,7 @@ static int mv3310_config_init(struct phy_device *phydev) 
{

	/* Check that the PHY interface type is compatible */

	if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&

	    phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&

	    phydev->interface != PHY_INTERFACE_MODE_XAUI &&

	    phydev->interface != PHY_INTERFACE_MODE_RXAUI &&

	    phydev->interface != PHY_INTERFACE_MODE_10GKR)
@@ -313,18 +314,29 @@ static int mv3310_aneg_done(struct phy_device *phydev) 
static void mv3310_update_interface(struct phy_device *phydev)

{

	if ((phydev->interface == PHY_INTERFACE_MODE_SGMII ||

	     phydev->interface == PHY_INTERFACE_MODE_2500BASEX ||

	     phydev->interface == PHY_INTERFACE_MODE_10GKR) && phydev->link) {

		/* The PHY automatically switches its serdes interface (and

		 * active PHYXS instance) between Cisco SGMII and 10GBase-KR

		 * modes according to the speed.  Florian suggests setting

		 * phydev->interface to communicate this to the MAC. Only do

		 * this if we are already in either SGMII or 10GBase-KR mode.

		 * active PHYXS instance) between Cisco SGMII, 10GBase-KR and

		 * 2500BaseX modes according to the speed.  Florian suggests

		 * setting phydev->interface to communicate this to the MAC.

		 * Only do this if we are already in one of the above modes.

		 */

		if (phydev->speed == SPEED_10000)

		switch (phydev->speed) {

		case SPEED_10000:

			phydev->interface = PHY_INTERFACE_MODE_10GKR;

		else if (phydev->speed >= SPEED_10 &&

			 phydev->speed < SPEED_10000)

			break;

		case SPEED_2500:

			phydev->interface = PHY_INTERFACE_MODE_2500BASEX;

			break;

		case SPEED_1000:

		case SPEED_100:

		case SPEED_10:

			phydev->interface = PHY_INTERFACE_MODE_SGMII;

			break;

		default:

			break;

		}

	}

}

CRA Git | Maintained and supported by SUSTech CRA and CCSE