Commit dc0b1aa3 authored by Linus Walleij's avatar Linus Walleij
Browse files

pinctrl: support pinconfig on the U300 



This adds pin configuration support for the U300 driver pair,
we can now read out the biasing and drive mode in debugfs and
configure it using the new configuration API.

ChangeLog v1->v2:
- Migrate to pin config and generic pin config changes.
ChangeLog v2->v3:
- Adjust to generic pin config changes in v7 patch set.

Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent a050b3ee

drivers/pinctrl/Kconfig

+1 −0
Original line number Diff line number Diff line
@@ -73,6 +73,7 @@ config PINCTRL_U300 
	bool "U300 pin controller driver"

	depends on ARCH_U300

	select PINMUX

	select GENERIC_PINCONF



config PINCTRL_COH901

	bool "ST-Ericsson U300 COH 901 335/571 GPIO"

drivers/pinctrl/pinctrl-coh901.c

+69 −8
Original line number Diff line number Diff line
@@ -23,7 +23,9 @@ 
#include <linux/list.h>

#include <linux/slab.h>

#include <linux/pinctrl/consumer.h>

#include <linux/pinctrl/pinconf-generic.h>

#include <mach/gpio-u300.h>

#include "pinctrl-coh901.h"



/*

 * Register definitions for COH 901 335 variant
@@ -418,8 +420,68 @@ static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset) 
	return retirq;

}



static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,

			    enum pin_config_param param, unsigned long data)

/* Returning -EINVAL means "supported but not available" */

int u300_gpio_config_get(struct gpio_chip *chip,

			 unsigned offset,

			 unsigned long *config)

{

	struct u300_gpio *gpio = to_u300_gpio(chip);

	enum pin_config_param param = (enum pin_config_param) *config;

	bool biasmode;

	u32 drmode;



	/* One bit per pin, clamp to bool range */

	biasmode = !!(readl(U300_PIN_REG(offset, per)) & U300_PIN_BIT(offset));



	/* Mask out the two bits for this pin and shift to bits 0,1 */

	drmode = readl(U300_PIN_REG(offset, pcr));

	drmode &= (U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));

	drmode >>= ((offset & 0x07) << 1);



	switch(param) {

	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:

		*config = 0;

		if (biasmode)

			return 0;

		else

			return -EINVAL;

		break;

	case PIN_CONFIG_BIAS_PULL_UP:

		*config = 0;

		if (!biasmode)

			return 0;

		else

			return -EINVAL;

		break;

	case PIN_CONFIG_DRIVE_PUSH_PULL:

		*config = 0;

		if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL)

			return 0;

		else

			return -EINVAL;

		break;

	case PIN_CONFIG_DRIVE_OPEN_DRAIN:

		*config = 0;

		if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN)

			return 0;

		else

			return -EINVAL;

		break;

	case PIN_CONFIG_DRIVE_OPEN_SOURCE:

		*config = 0;

		if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE)

			return 0;

		else

			return -EINVAL;

		break;

	default:

		break;

	}

	return -ENOTSUPP;

}



int u300_gpio_config_set(struct gpio_chip *chip, unsigned offset,

			 enum pin_config_param param)

{

	struct u300_gpio *gpio = to_u300_gpio(chip);

	unsigned long flags;
@@ -620,13 +682,12 @@ static void __init u300_gpio_init_pin(struct u300_gpio *gpio, 
		u300_gpio_direction_output(&gpio->chip, offset, conf->outval);



		/* Deactivate bias mode for output */

		u300_gpio_config(&gpio->chip, offset,

				 PIN_CONFIG_BIAS_HIGH_IMPEDANCE,

				 0);

		u300_gpio_config_set(&gpio->chip, offset,

				     PIN_CONFIG_BIAS_HIGH_IMPEDANCE);



		/* Set drive mode for output */

		u300_gpio_config(&gpio->chip, offset,

				 PIN_CONFIG_DRIVE_PUSH_PULL, 0);

		u300_gpio_config_set(&gpio->chip, offset,

				     PIN_CONFIG_DRIVE_PUSH_PULL);



		dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",

			offset, conf->outval);
@@ -637,7 +698,7 @@ static void __init u300_gpio_init_pin(struct u300_gpio *gpio, 
		u300_gpio_set(&gpio->chip, offset, 0);



		/* Set bias mode for input */

		u300_gpio_config(&gpio->chip, offset, conf->bias_mode, 0);

		u300_gpio_config_set(&gpio->chip, offset, conf->bias_mode);



		dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",

			offset, conf->bias_mode);

drivers/pinctrl/pinctrl-coh901.h

0 → 100644
+5 −0
Original line number Diff line number Diff line 
int u300_gpio_config_get(struct gpio_chip *chip,

			 unsigned offset,

			 unsigned long *config);

int u300_gpio_config_set(struct gpio_chip *chip, unsigned offset,

			 enum pin_config_param param);

drivers/pinctrl/pinctrl-u300.c

+60 −0
Original line number Diff line number Diff line
@@ -19,6 +19,9 @@ 
#include <linux/err.h>

#include <linux/pinctrl/pinctrl.h>

#include <linux/pinctrl/pinmux.h>

#include <linux/pinctrl/pinconf.h>

#include <linux/pinctrl/pinconf-generic.h>

#include "pinctrl-coh901.h"



/*

 * Register definitions for the U300 Padmux control registers in the
@@ -1044,12 +1047,69 @@ static struct pinctrl_gpio_range u300_gpio_ranges[] = { 
	U300_GPIO_RANGE(25, 181, 1),

};



static struct pinctrl_gpio_range *u300_match_gpio_range(unsigned pin)

{

	int i;



	for (i = 0; i < ARRAY_SIZE(u300_gpio_ranges); i++) {

		struct pinctrl_gpio_range *range;



		range = &u300_gpio_ranges[i];

		if (pin >= range->pin_base &&

		    pin <= (range->pin_base + range->npins - 1))

			return range;

	}

	return NULL;

}



int u300_pin_config_get(struct pinctrl_dev *pctldev,

			unsigned pin,

			unsigned long *config)

{

	struct pinctrl_gpio_range *range = u300_match_gpio_range(pin);



	/* We get config for those pins we CAN get it for and that's it */

	if (!range)

		return -ENOTSUPP;



	return u300_gpio_config_get(range->gc,

				    (pin - range->pin_base + range->base),

				    config);

}



int u300_pin_config_set(struct pinctrl_dev *pctldev,

			unsigned pin,

			unsigned long config)

{

	struct pinctrl_gpio_range *range = u300_match_gpio_range(pin);

	int ret;



	if (!range)

		return -EINVAL;



	/* Note: none of these configurations take any argument */

	ret = u300_gpio_config_set(range->gc,

				   (pin - range->pin_base + range->base),

				   pinconf_to_config_param(config));

	if (ret)

		return ret;



	return 0;

}



static struct pinconf_ops u300_pconf_ops = {

	.is_generic = true,

	.pin_config_get = u300_pin_config_get,

	.pin_config_set = u300_pin_config_set,

};



static struct pinctrl_desc u300_pmx_desc = {

	.name = DRIVER_NAME,

	.pins = u300_pads,

	.npins = ARRAY_SIZE(u300_pads),

	.pctlops = &u300_pctrl_ops,

	.pmxops = &u300_pmx_ops,

	.confops = &u300_pconf_ops,

	.owner = THIS_MODULE,

};

CRA Git | Maintained and supported by SUSTech CRA and CCSE