Commit da7ac948 authored by Chen-Yu Tsai's avatar Chen-Yu Tsai Committed by Maxime Ripard
Browse files

ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra 



The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
form factor and position of various connectors, leds and buttons is
similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
as the latest Banana Pi M64.

It features:

  - X-Powers AXP221s PMIC connected to i2c0
  - 2 GB DDR3 DRAM
  - 8 GB eMMC
  - micro SD card slot
  - DC power jack
  - HDMI output
  - MIPI DSI connector
  - 2x USB 2.0 hosts
  - 1x USB 2.0 OTG
  - gigabit ethernet with Realtek RTL8211E transceiver
  - WiFi/Bluetooth with AP6212 chip, with external antenna connector
  - SATA and power connectors for native SATA support
  - camera sensor connector
  - consumer IR receiver
  - audio out headphone jack
  - onboard microphone
  - red, green, and blue LEDs
  - debug UART pins
  - Li-Po battery connector
  - Raspberry Pi B+ compatible GPIO header
  - power, reset, and boot control buttons

This patch adds a dts file that enables UART, MMC and PMIC support.

Signed-off-by: default avatarChen-Yu Tsai <wens@csie.org>
Signed-off-by: default avatarIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 195a59ab

arch/arm/boot/dts/Makefile

+1 −0
Original line number Diff line number Diff line
@@ -933,6 +933,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ 
	sun8i-h3-orangepi-plus2e.dtb \

	sun8i-r16-bananapi-m2m.dtb \

	sun8i-r16-parrot.dtb \

	sun8i-r40-bananapi-m2-ultra.dtb \

	sun8i-v3s-licheepi-zero.dtb \

	sun8i-v3s-licheepi-zero-dock.dtb

dtb-$(CONFIG_MACH_SUN9I) += \

arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

0 → 100644
+178 −0
Original line number Diff line number Diff line 
/*

 * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>

 * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>

 *

 * This file is dual-licensed: you can use it either under the terms

 * of the GPL or the X11 license, at your option. Note that this dual

 * licensing only applies to this file, and not this project as a

 * whole.

 *

 *  a) This file is free software; you can redistribute it and/or

 *     modify it under the terms of the GNU General Public License as

 *     published by the Free Software Foundation; either version 2 of the

 *     License, or (at your option) any later version.

 *

 *     This file is distributed in the hope that it will be useful,

 *     but WITHOUT ANY WARRANTY; without even the implied warranty of

 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 *     GNU General Public License for more details.

 *

 * Or, alternatively,

 *

 *  b) Permission is hereby granted, free of charge, to any person

 *     obtaining a copy of this software and associated documentation

 *     files (the "Software"), to deal in the Software without

 *     restriction, including without limitation the rights to use,

 *     copy, modify, merge, publish, distribute, sublicense, and/or

 *     sell copies of the Software, and to permit persons to whom the

 *     Software is furnished to do so, subject to the following

 *     conditions:

 *

 *     The above copyright notice and this permission notice shall be

 *     included in all copies or substantial portions of the Software.

 *

 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES

 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT

 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR

 *     OTHER DEALINGS IN THE SOFTWARE.

 */



/dts-v1/;

#include "sun8i-r40.dtsi"



#include <dt-bindings/gpio/gpio.h>



/ {

	model = "Banana Pi BPI-M2-Ultra";

	compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40";



	aliases {

		serial0 = &uart0;

	};



	chosen {

		stdout-path = "serial0:115200n8";

	};



	leds {

		compatible = "gpio-leds";



		pwr-led {

			label = "bananapi:red:pwr";

			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;

			default-state = "on";

		};



		user-led-green {

			label = "bananapi:green:user";

			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;

		};



		user-led-blue {

			label = "bananapi:blue:user";

			gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>;

		};

	};



	wifi_pwrseq: wifi_pwrseq {

		compatible = "mmc-pwrseq-simple";

		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */

	};

};



&i2c0 {

	status = "okay";



	axp22x: pmic@34 {

		compatible = "x-powers,axp221";

		reg = <0x34>;

		interrupt-parent = <&nmi_intc>;

		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;

	};

};



#include "axp22x.dtsi"



&reg_aldo3 {

	regulator-always-on;

	regulator-min-microvolt = <2700000>;

	regulator-max-microvolt = <3300000>;

	regulator-name = "avcc";

};



&reg_dcdc1 {

	regulator-always-on;

	regulator-min-microvolt = <3000000>;

	regulator-max-microvolt = <3000000>;

	regulator-name = "vcc-3v0";

};



&reg_dcdc2 {

	regulator-always-on;

	regulator-min-microvolt = <1000000>;

	regulator-max-microvolt = <1300000>;

	regulator-name = "vdd-cpu";

};



&reg_dcdc3 {

	regulator-always-on;

	regulator-min-microvolt = <1000000>;

	regulator-max-microvolt = <1300000>;

	regulator-name = "vdd-sys";

};



&reg_dcdc5 {

	regulator-always-on;

	regulator-min-microvolt = <1500000>;

	regulator-max-microvolt = <1500000>;

	regulator-name = "vcc-dram";

};



&reg_dldo1 {

	regulator-min-microvolt = <1800000>;

	regulator-max-microvolt = <3300000>;

	regulator-name = "vcc-wifi-io";

};



&reg_dldo2 {

	regulator-min-microvolt = <3300000>;

	regulator-max-microvolt = <3300000>;

	regulator-name = "vcc-wifi";

};



&mmc0 {

	vmmc-supply = <&reg_dcdc1>;

	bus-width = <4>;

	cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */

	cd-inverted;

	status = "okay";

};



&mmc1 {

	pinctrl-names = "default";

	pinctrl-0 = <&mmc1_pg_pins>;

	vmmc-supply = <&reg_dldo2>;

	vqmmc-supply = <&reg_dldo1>;

	mmc-pwrseq = <&wifi_pwrseq>;

	bus-width = <4>;

	non-removable;

	status = "okay";

};



&mmc2 {

	vmmc-supply = <&reg_dcdc1>;

	vqmmc-supply = <&reg_dcdc1>;

	bus-width = <8>;

	non-removable;

	status = "okay";

};



&uart0 {

	pinctrl-names = "default";

	pinctrl-0 = <&uart0_pb_pins>;

	status = "okay";

};

CRA Git | Maintained and supported by SUSTech CRA and CCSE