Commit c4a6bf7f authored by Darrick J. Wong's avatar Darrick J. Wong
Browse files

xfs: don't ever put nlink > 0 inodes on the unlinked list 



When XFS creates an O_TMPFILE file, the inode is created with nlink = 1,
put on the unlinked list, and then the VFS sets nlink = 0 in d_tmpfile.
If we crash before anything logs the inode (it's dirty incore but the
vfs doesn't tell us it's dirty so we never log that change), the iunlink
processing part of recovery will then explode with a pile of:

XFS: Assertion failed: VFS_I(ip)->i_nlink == 0, file:
fs/xfs/xfs_log_recover.c, line: 5072

Worse yet, since nlink is nonzero, the inodes also don't get cleaned up
and they just leak until the next xfs_repair run.

Therefore, change xfs_iunlink to require that inodes being put on the
unlinked list have nlink == 0, change the tmpfile callers to instantiate
nodes that way, and set the nlink to 1 just prior to calling d_tmpfile.
Fix the comment for xfs_iunlink while we're at it.

Signed-off-by: default avatarDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: default avatarChristoph Hellwig <hch@lst.de>
parent 15a268d9

fs/xfs/xfs_inode.c

+6 −10
Original line number Diff line number Diff line
@@ -1332,7 +1332,7 @@ xfs_create_tmpfile( 
	if (error)

		goto out_trans_cancel;



	error = xfs_dir_ialloc(&tp, dp, mode, 1, 0, prid, &ip);

	error = xfs_dir_ialloc(&tp, dp, mode, 0, 0, prid, &ip);

	if (error)

		goto out_trans_cancel;
@@ -2231,11 +2231,8 @@ out: 
}



/*

 * This is called when the inode's link count goes to 0 or we are creating a

 * tmpfile via O_TMPFILE. In the case of a tmpfile, @ignore_linkcount will be

 * set to true as the link count is dropped to zero by the VFS after we've

 * created the file successfully, so we have to add it to the unlinked list

 * while the link count is non-zero.

 * This is called when the inode's link count has gone to 0 or we are creating

 * a tmpfile via O_TMPFILE.  The inode @ip must have nlink == 0.

 *

 * We place the on-disk inode on a list in the AGI.  It will be pulled from this

 * list when the inode is freed.
@@ -2254,6 +2251,7 @@ xfs_iunlink( 
	short			bucket_index = agino % XFS_AGI_UNLINKED_BUCKETS;

	int			error;



	ASSERT(VFS_I(ip)->i_nlink == 0);

	ASSERT(VFS_I(ip)->i_mode != 0);

	trace_xfs_iunlink(ip);
@@ -3184,11 +3182,9 @@ xfs_rename_alloc_whiteout( 


	/*

	 * Prepare the tmpfile inode as if it were created through the VFS.

	 * Otherwise, the link increment paths will complain about nlink 0->1.

	 * Drop the link count as done by d_tmpfile(), complete the inode setup

	 * and flag it as linkable.

	 * Complete the inode setup and flag it as linkable.  nlink is already

	 * zero, so we can skip the drop_nlink.

	 */

	drop_nlink(VFS_I(tmpfile));

	xfs_setup_iops(tmpfile);

	xfs_finish_inode_setup(tmpfile);

	VFS_I(tmpfile)->i_state |= I_LINKABLE;

fs/xfs/xfs_iops.c

+11 −2
Original line number Diff line number Diff line
@@ -191,9 +191,18 @@ xfs_generic_create( 


	xfs_setup_iops(ip);



	if (tmpfile)

	if (tmpfile) {

		/*

		 * The VFS requires that any inode fed to d_tmpfile must have

		 * nlink == 1 so that it can decrement the nlink in d_tmpfile.

		 * However, we created the temp file with nlink == 0 because

		 * we're not allowed to put an inode with nlink > 0 on the

		 * unlinked list.  Therefore we have to set nlink to 1 so that

		 * d_tmpfile can immediately set it back to zero.

		 */

		set_nlink(inode, 1);

		d_tmpfile(dentry, inode);

	else

	} else

		d_instantiate(dentry, inode);



	xfs_finish_inode_setup(ip);

CRA Git | Maintained and supported by SUSTech CRA and CCSE