Commit b31a7654 authored by Arnd Bergmann's avatar Arnd Bergmann
Browse files

Merge tag 'omap-for-v3.11/board-signed' of... 

Merge tag 'omap-for-v3.11/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards

From Tony Lindgren:

Minor board changes for v3.11 merge window. These are
tapering down finally as we're getting closer to making
omap2+ DT only.

* tag 'omap-for-v3.11/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap

:
  ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
  ARM: OMAP1: nokia770: enable Tahvo
  ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
  arm: omap: board-overo: reset GPIO for SMSC911x

Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
parents 4a77a932 45853507

Documentation/bcache.txt

+9 −3
Original line number Diff line number Diff line
@@ -319,7 +319,10 @@ cache<0..n> 
  Symlink to each of the cache devices comprising this cache set. 



cache_available_percent

  Percentage of cache device free.

  Percentage of cache device which doesn't contain dirty data, and could

  potentially be used for writeback.  This doesn't mean this space isn't used

  for clean cached data; the unused statistic (in priority_stats) is typically

  much lower.



clear_stats

  Clears the statistics associated with this cache
@@ -423,8 +426,11 @@ nbuckets 
  Total buckets in this cache



priority_stats

  Statistics about how recently data in the cache has been accessed.  This can

  reveal your working set size.

  Statistics about how recently data in the cache has been accessed.

  This can reveal your working set size.  Unused is the percentage of

  the cache that doesn't contain any data.  Metadata is bcache's

  metadata overhead.  Average is the average priority of cache buckets.

  Next is a list of quantiles with the priority threshold of each.



written

  Sum of all data that has been written to the cache; comparison with

Documentation/devices.txt

+2 −6
Original line number Diff line number Diff line
@@ -498,12 +498,8 @@ Your cooperation is appreciated. 


		Each device type has 5 bits (32 minors).



 13 block	8-bit MFM/RLL/IDE controller

		  0 = /dev/xda		First XT disk whole disk

		 64 = /dev/xdb		Second XT disk whole disk



		Partitions are handled in the same way as IDE disks

		(see major number 3).

 13 block	Previously used for the XT disk (/dev/xdN)

		Deleted in kernel v3.9.



 14 char	Open Sound System (OSS)

		  0 = /dev/mixer	Mixer control

Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt

+1 −1
Original line number Diff line number Diff line 
Atmel AT91RM9200 Real Time Clock



Required properties:

- compatible: should be: "atmel,at91rm9200-rtc"

- compatible: should be: "atmel,at91rm9200-rtc" or "atmel,at91sam9x5-rtc"

- reg: physical base address of the controller and length of memory mapped

  region.

- interrupts: rtc alarm/event interrupt

Documentation/dmatest.txt

+3 −3
Original line number Diff line number Diff line
@@ -34,7 +34,7 @@ command: 
After a while you will start to get messages about current status or error like

in the original code.



Note that running a new test will stop any in progress test.

Note that running a new test will not stop any in progress test.



The following command should return actual state of the test.

	% cat /sys/kernel/debug/dmatest/run
@@ -52,8 +52,8 @@ To wait for test done the user may perform a busy loop that checks the state. 


The module parameters that is supplied to the kernel command line will be used

for the first performed test. After user gets a control, the test could be

interrupted or re-run with same or different parameters. For the details see

the above section "Part 2 - When dmatest is built as a module..."

re-run with the same or different parameters. For the details see the above

section "Part 2 - When dmatest is built as a module..."



In both cases the module parameters are used as initial values for the test case.

You always could check them at run-time by running

Documentation/filesystems/xfs.txt

+3 −0
Original line number Diff line number Diff line
@@ -33,6 +33,9 @@ When mounting an XFS filesystem, the following options are accepted. 
	removing extended attributes) the on-disk superblock feature

	bit field will be updated to reflect this format being in use.



	CRC enabled filesystems always use the attr2 format, and so

	will reject the noattr2 mount option if it is set.



  barrier

	Enables the use of block layer write barriers for writes into

	the journal and unwritten extent conversion.  This allows for

CRA Git | Maintained and supported by SUSTech CRA and CCSE