Commit ac7c6669 authored by ODonnell, Michael's avatar ODonnell, Michael Committed by Jeff Garzik
Browse files

[PATCH] corruption during e100 MDI register access 



We have identified two related bugs in the e100 driver.

Both bugs are related to manipulation of the MDI control register.

The first problem is that the Ready bit is being ignored when writing to
the Control register; we noticed this because the Linux bonding driver
would occasionally come to the spurious conclusion that the link was down
when querying Link State.  It turned out that by failing to wait for a
previous command to complete it was selecting what was essentially a random
register in the MDI register set.  When we added code that waits for the
Ready bit (as shown in the patch file below) all such problems ceased.

The second problem is that, although access to the MDI registers involves
multiple steps which must not be intermixed, nothing was defending against
two or more threads attempting simultaneous access.  The most obvious
situation where such interference could occur involves the watchdog versus
ioctl paths, but there are probably others, so we recommend the locking
shown in our patch file.

Signed-off-by: default avatarMichael O'Donnell <Michael.ODonnell@stratus.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
Signed-off-by: default avatarJeff Garzik <jgarzik@pobox.com>
parent bf785ee0

drivers/net/e100.c

+29 −3
Original line number Diff line number Diff line
@@ -132,6 +132,10 @@ 
 * 	TODO:

 * 	o several entry points race with dev->close

 * 	o check for tx-no-resources/stop Q races with tx clean/wake Q

 *

 *	FIXES:

 * 2005/12/02 - Michael O'Donnell <Michael.ODonnell at stratus dot com>

 *	- Stratus87247: protect MDI control register manipulations

 */



#include <linux/config.h>
@@ -578,6 +582,7 @@ struct nic { 
	u16 leds;

	u16 eeprom_wc;

	u16 eeprom[256];

	spinlock_t mdio_lock;

};



static inline void e100_write_flush(struct nic *nic)
@@ -876,7 +881,27 @@ static u16 mdio_ctrl(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data) 
{

	u32 data_out = 0;

	unsigned int i;

	unsigned long flags;





	/*

	 * Stratus87247: we shouldn't be writing the MDI control

	 * register until the Ready bit shows True.  Also, since

	 * manipulation of the MDI control registers is a multi-step

	 * procedure it should be done under lock.

	 */

	spin_lock_irqsave(&nic->mdio_lock, flags);

	for (i = 100; i; --i) {

		if (readl(&nic->csr->mdi_ctrl) & mdi_ready)

			break;

		udelay(20);

	}

	if (unlikely(!i)) {

		printk("e100.mdio_ctrl(%s) won't go Ready\n",

			nic->netdev->name );

		spin_unlock_irqrestore(&nic->mdio_lock, flags);

		return 0;		/* No way to indicate timeout error */

	}

	writel((reg << 16) | (addr << 21) | dir | data, &nic->csr->mdi_ctrl);



	for (i = 0; i < 100; i++) {
@@ -884,7 +909,7 @@ static u16 mdio_ctrl(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data) 
		if ((data_out = readl(&nic->csr->mdi_ctrl)) & mdi_ready)

			break;

	}



	spin_unlock_irqrestore(&nic->mdio_lock, flags);

	DPRINTK(HW, DEBUG,

		"%s:addr=%d, reg=%d, data_in=0x%04X, data_out=0x%04X\n",

		dir == mdi_read ? "READ" : "WRITE", addr, reg, data, data_out);
@@ -2562,6 +2587,7 @@ static int __devinit e100_probe(struct pci_dev *pdev, 
	/* locks must be initialized before calling hw_reset */

	spin_lock_init(&nic->cb_lock);

	spin_lock_init(&nic->cmd_lock);

	spin_lock_init(&nic->mdio_lock);



	/* Reset the device before pci_set_master() in case device is in some

	 * funky state and has an interrupt pending - hint: we don't have the

CRA Git | Maintained and supported by SUSTech CRA and CCSE