Documentation DMA-API-HOWTO.txt Add dma mapping error check usage examples (8d7f62e6) · Commits · 戴 / test

Documentation/DMA-API-HOWTO.txt

+126 −0

Original line number	Diff line number	Diff line
		@@ -468,11 +468,46 @@ To map a single region, you do:
		size_t size = buffer->len;

		dma_handle = dma_map_single(dev, addr, size, direction);
		if (dma_mapping_error(dma_handle)) {
		/*
		* reduce current DMA mapping usage,
		* delay and try again later or
		* reset driver.
		*/
		goto map_error_handling;
		}

		and to unmap it:

		dma_unmap_single(dev, dma_handle, size, direction);

		You should call dma_mapping_error() as dma_map_single() could fail and return
		error. Not all dma implementations support dma_mapping_error() interface.
		However, it is a good practice to call dma_mapping_error() interface, which
		will invoke the generic mapping error check interface. Doing so will ensure
		that the mapping code will work correctly on all dma implementations without
		any dependency on the specifics of the underlying implementation. Using the
		returned address without checking for errors could result in failures ranging
		from panics to silent data corruption. Couple of example of incorrect ways to
		check for errors that make assumptions about the underlying dma implementation
		are as follows and these are applicable to dma_map_page() as well.

		Incorrect example 1:
		dma_addr_t dma_handle;

		dma_handle = dma_map_single(dev, addr, size, direction);
		if ((dma_handle & 0xffff != 0) \|\| (dma_handle >= 0x1000000)) {
		goto map_error;
		}

		Incorrect example 2:
		dma_addr_t dma_handle;

		dma_handle = dma_map_single(dev, addr, size, direction);
		if (dma_handle == DMA_ERROR_CODE) {
		goto map_error;
		}

		You should call dma_unmap_single when the DMA activity is finished, e.g.
		from the interrupt which told you that the DMA transfer is done.

		@@ -489,6 +524,14 @@ Specifically:
		size_t size = buffer->len;

		dma_handle = dma_map_page(dev, page, offset, size, direction);
		if (dma_mapping_error(dma_handle)) {
		/*
		* reduce current DMA mapping usage,
		* delay and try again later or
		* reset driver.
		*/
		goto map_error_handling;
		}

		...

		@@ -496,6 +539,12 @@ Specifically:

		Here, "offset" means byte offset within the given page.

		You should call dma_mapping_error() as dma_map_page() could fail and return
		error as outlined under the dma_map_single() discussion.

		You should call dma_unmap_page when the DMA activity is finished, e.g.
		from the interrupt which told you that the DMA transfer is done.

		With scatterlists, you map a region gathered from several regions by:

		int i, count = dma_map_sg(dev, sglist, nents, direction);
		@@ -578,6 +627,14 @@ to use the dma_sync_*() interfaces.
		dma_addr_t mapping;

		mapping = dma_map_single(cp->dev, buffer, len, DMA_FROM_DEVICE);
		if (dma_mapping_error(dma_handle)) {
		/*
		* reduce current DMA mapping usage,
		* delay and try again later or
		* reset driver.
		*/
		goto map_error_handling;
		}

		cp->rx_buf = buffer;
		cp->rx_len = len;
		@@ -658,6 +715,75 @@ failure can be determined by:
		* delay and try again later or
		* reset driver.
		*/
		goto map_error_handling;
		}

		- unmap pages that are already mapped, when mapping error occurs in the middle
		of a multiple page mapping attempt. These example are applicable to
		dma_map_page() as well.

		Example 1:
		dma_addr_t dma_handle1;
		dma_addr_t dma_handle2;

		dma_handle1 = dma_map_single(dev, addr, size, direction);
		if (dma_mapping_error(dev, dma_handle1)) {
		/*
		* reduce current DMA mapping usage,
		* delay and try again later or
		* reset driver.
		*/
		goto map_error_handling1;
		}
		dma_handle2 = dma_map_single(dev, addr, size, direction);
		if (dma_mapping_error(dev, dma_handle2)) {
		/*
		* reduce current DMA mapping usage,
		* delay and try again later or
		* reset driver.
		*/
		goto map_error_handling2;
		}

		...

		map_error_handling2:
		dma_unmap_single(dma_handle1);
		map_error_handling1:

		Example 2: (if buffers are allocated a loop, unmap all mapped buffers when
		mapping error is detected in the middle)

		dma_addr_t dma_addr;
		dma_addr_t array[DMA_BUFFERS];
		int save_index = 0;

		for (i = 0; i < DMA_BUFFERS; i++) {

		...

		dma_addr = dma_map_single(dev, addr, size, direction);
		if (dma_mapping_error(dev, dma_addr)) {
		/*
		* reduce current DMA mapping usage,
		* delay and try again later or
		* reset driver.
		*/
		goto map_error_handling;
		}
		array[i].dma_addr = dma_addr;
		save_index++;
		}

		...

		map_error_handling:

		for (i = 0; i < save_index; i++) {

		...

		dma_unmap_single(array[i].dma_addr);
		}

		Networking drivers must call dev_kfree_skb to free the socket buffer

Admin message