Commit 72001762 authored by Andreas Mohr's avatar Andreas Mohr Committed by David S. Miller
Browse files

e100: add non-MII PHY support 



Restore support for cards with MII-lacking PHYs as compared to removed
pre-2.6.29 eepro100 driver: use full low-level MII I/O access abstraction
by providing clean PHY-specific mdio_ctrl() functions for either standard
MII-compliant cards, slightly special ones or non-MII PHY ones.

We now have another netdev_priv member for mdio_ctrl(), thus we have some
array indirection, but we save some additional opcodes for specific
phy_82552_v handling in the common case.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: default avatarAndreas Mohr <andi@lisas.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent e5241c44

drivers/net/e100.c

+162 −26
Original line number Diff line number Diff line
@@ -143,6 +143,8 @@ 
 *	FIXES:

 * 2005/12/02 - Michael O'Donnell <Michael.ODonnell at stratus dot com>

 *	- Stratus87247: protect MDI control register manipulations

 * 2009/06/01 - Andreas Mohr <andi at lisas dot de>

 *      - add clean lowlevel I/O emulation for cards with MII-lacking PHYs

 */



#include <linux/module.h>
@@ -372,6 +374,7 @@ enum eeprom_op { 


enum eeprom_offsets {

	eeprom_cnfg_mdix  = 0x03,

	eeprom_phy_iface  = 0x06,

	eeprom_id         = 0x0A,

	eeprom_config_asf = 0x0D,

	eeprom_smbus_addr = 0x90,
@@ -381,6 +384,18 @@ enum eeprom_cnfg_mdix { 
	eeprom_mdix_enabled = 0x0080,

};



enum eeprom_phy_iface {

	NoSuchPhy = 0,

	I82553AB,

	I82553C,

	I82503,

	DP83840,

	S80C240,

	S80C24,

	I82555,

	DP83840A = 10,

};



enum eeprom_id {

	eeprom_id_wol = 0x0020,

};
@@ -545,6 +560,7 @@ struct nic { 
	u32 msg_enable				____cacheline_aligned;

	struct net_device *netdev;

	struct pci_dev *pdev;

	u16 (*mdio_ctrl)(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data);



	struct rx *rxs				____cacheline_aligned;

	struct rx *rx_to_use;
@@ -899,7 +915,21 @@ err_unlock: 
	return err;

}



static u16 mdio_ctrl(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data)

static int mdio_read(struct net_device *netdev, int addr, int reg)

{

	struct nic *nic = netdev_priv(netdev);

	return nic->mdio_ctrl(nic, addr, mdi_read, reg, 0);

}



static void mdio_write(struct net_device *netdev, int addr, int reg, int data)

{

	struct nic *nic = netdev_priv(netdev);



	nic->mdio_ctrl(nic, addr, mdi_write, reg, data);

}



/* the standard mdio_ctrl() function for usual MII-compliant hardware */

static u16 mdio_ctrl_hw(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data)

{

	u32 data_out = 0;

	unsigned int i;
@@ -938,18 +968,17 @@ static u16 mdio_ctrl(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data) 
	return (u16)data_out;

}



static int mdio_read(struct net_device *netdev, int addr, int reg)

/* slightly tweaked mdio_ctrl() function for phy_82552_v specifics */

static u16 mdio_ctrl_phy_82552_v(struct nic *nic,

				 u32 addr,

				 u32 dir,

				 u32 reg,

				 u16 data)

{

	return mdio_ctrl(netdev_priv(netdev), addr, mdi_read, reg, 0);

}



static void mdio_write(struct net_device *netdev, int addr, int reg, int data)

{

	struct nic *nic = netdev_priv(netdev);



	if  ((nic->phy == phy_82552_v) && (reg == MII_BMCR) &&

	     (data & (BMCR_ANRESTART | BMCR_ANENABLE))) {

		u16 advert = mdio_read(netdev, nic->mii.phy_id, MII_ADVERTISE);

	if ((reg == MII_BMCR) && (dir == mdi_write)) {

		if (data & (BMCR_ANRESTART | BMCR_ANENABLE)) {

			u16 advert = mdio_read(nic->netdev, nic->mii.phy_id,

							MII_ADVERTISE);



			/*

			 * Workaround Si issue where sometimes the part will not
@@ -960,8 +989,62 @@ static void mdio_write(struct net_device *netdev, int addr, int reg, int data) 
			else if (advert & ADVERTISE_100HALF)

				data |= BMCR_SPEED100;

		}

	}

	return mdio_ctrl_hw(nic, addr, dir, reg, data);

}



	mdio_ctrl(netdev_priv(netdev), addr, mdi_write, reg, data);

/* Fully software-emulated mdio_ctrl() function for cards without

 * MII-compliant PHYs.

 * For now, this is mainly geared towards 80c24 support; in case of further

 * requirements for other types (i82503, ...?) either extend this mechanism

 * or split it, whichever is cleaner.

 */

static u16 mdio_ctrl_phy_mii_emulated(struct nic *nic,

				      u32 addr,

				      u32 dir,

				      u32 reg,

				      u16 data)

{

	/* might need to allocate a netdev_priv'ed register array eventually

	 * to be able to record state changes, but for now

	 * some fully hardcoded register handling ought to be ok I guess. */



	if (dir == mdi_read) {

		switch (reg) {

		case MII_BMCR:

			/* Auto-negotiation, right? */

			return  BMCR_ANENABLE |

				BMCR_FULLDPLX;

		case MII_BMSR:

			return	BMSR_LSTATUS /* for mii_link_ok() */ |

				BMSR_ANEGCAPABLE |

				BMSR_10FULL;

		case MII_ADVERTISE:

			/* 80c24 is a "combo card" PHY, right? */

			return	ADVERTISE_10HALF |

				ADVERTISE_10FULL;

		default:

			DPRINTK(HW, DEBUG,

		"%s:addr=%d, reg=%d, data=0x%04X: unimplemented emulation!\n",

		dir == mdi_read ? "READ" : "WRITE", addr, reg, data);

			return 0xFFFF;

		}

	} else {

		switch (reg) {

		default:

			DPRINTK(HW, DEBUG,

		"%s:addr=%d, reg=%d, data=0x%04X: unimplemented emulation!\n",

		dir == mdi_read ? "READ" : "WRITE", addr, reg, data);

			return 0xFFFF;

		}

	}

}

static inline int e100_phy_supports_mii(struct nic *nic)

{

	/* for now, just check it by comparing whether we

	   are using MII software emulation.

	*/

	return (nic->mdio_ctrl != mdio_ctrl_phy_mii_emulated);

}



static void e100_get_defaults(struct nic *nic)
@@ -1013,7 +1096,8 @@ static void e100_configure(struct nic *nic, struct cb *cb, struct sk_buff *skb) 
	config->standard_stat_counter = 0x1;	/* 1=standard, 0=extended */

	config->rx_discard_short_frames = 0x1;	/* 1=discard, 0=pass */

	config->tx_underrun_retry = 0x3;	/* # of underrun retries */

	config->mii_mode = 0x1;			/* 1=MII mode, 0=503 mode */

	if (e100_phy_supports_mii(nic))

		config->mii_mode = 1;           /* 1=MII mode, 0=i82503 mode */

	config->pad10 = 0x6;

	config->no_source_addr_insertion = 0x1;	/* 1=no, 0=yes */

	config->preamble_length = 0x2;		/* 0=1, 1=3, 2=7, 3=15 bytes */
@@ -1270,6 +1354,42 @@ static void e100_dump(struct nic *nic, struct cb *cb, struct sk_buff *skb) 
		offsetof(struct mem, dump_buf));

}



static int e100_phy_check_without_mii(struct nic *nic)

{

	u8 phy_type;

	int without_mii;



	phy_type = (nic->eeprom[eeprom_phy_iface] >> 8) & 0x0f;



	switch (phy_type) {

	case NoSuchPhy: /* Non-MII PHY; UNTESTED! */

	case I82503: /* Non-MII PHY; UNTESTED! */

	case S80C24: /* Non-MII PHY; tested and working */

		/* paragraph from the FreeBSD driver, "FXP_PHY_80C24":

		 * The Seeq 80c24 AutoDUPLEX(tm) Ethernet Interface Adapter

		 * doesn't have a programming interface of any sort.  The

		 * media is sensed automatically based on how the link partner

		 * is configured.  This is, in essence, manual configuration.

		 */

		DPRINTK(PROBE, INFO,

			 "found MII-less i82503 or 80c24 or other PHY\n");



		nic->mdio_ctrl = mdio_ctrl_phy_mii_emulated;

		nic->mii.phy_id = 0; /* is this ok for an MII-less PHY? */



		/* these might be needed for certain MII-less cards...

		 * nic->flags |= ich;

		 * nic->flags |= ich_10h_workaround; */



		without_mii = 1;

		break;

	default:

		without_mii = 0;

		break;

	}

	return without_mii;

}



#define NCONFIG_AUTO_SWITCH	0x0080

#define MII_NSC_CONG		MII_RESV1

#define NSC_CONG_ENABLE		0x0100
@@ -1290,9 +1410,21 @@ static int e100_phy_init(struct nic *nic) 
		if (!((bmcr == 0xFFFF) || ((stat == 0) && (bmcr == 0))))

			break;

	}

	DPRINTK(HW, DEBUG, "phy_addr = %d\n", nic->mii.phy_id);

	if (addr == 32)

	if (addr == 32) {

		/* uhoh, no PHY detected: check whether we seem to be some

		 * weird, rare variant which is *known* to not have any MII.

		 * But do this AFTER MII checking only, since this does

		 * lookup of EEPROM values which may easily be unreliable. */

		if (e100_phy_check_without_mii(nic))

			return 0; /* simply return and hope for the best */

		else {

			/* for unknown cases log a fatal error */

			DPRINTK(HW, ERR,

				"Failed to locate any known PHY, aborting.\n");

			return -EAGAIN;

		}

	} else

		DPRINTK(HW, DEBUG, "phy_addr = %d\n", nic->mii.phy_id);



	/* Isolate all the PHY ids */

	for (addr = 0; addr < 32; addr++)
@@ -1320,6 +1452,9 @@ static int e100_phy_init(struct nic *nic) 
	if (nic->phy == phy_82552_v) {

		u16 advert = mdio_read(netdev, nic->mii.phy_id, MII_ADVERTISE);



		/* assign special tweaked mdio_ctrl() function */

		nic->mdio_ctrl = mdio_ctrl_phy_82552_v;



		/* Workaround Si not advertising flow-control during autoneg */

		advert |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM;

		mdio_write(netdev, nic->mii.phy_id, MII_ADVERTISE, advert);
@@ -2585,6 +2720,7 @@ static int __devinit e100_probe(struct pci_dev *pdev, 
	nic->netdev = netdev;

	nic->pdev = pdev;

	nic->msg_enable = (1 << debug) - 1;

	nic->mdio_ctrl = mdio_ctrl_hw;

	pci_set_drvdata(pdev, netdev);



	if ((err = pci_enable_device(pdev))) {

CRA Git | Maintained and supported by SUSTech CRA and CCSE