Merge tag 'nand/for-4.12' of github.com:linux-nand/linux into MTD

Atmel NAND flash

Atmel NAND flash controller bindings

The NAND flash controller node should be defined under the EBI bus (see

Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).

One or several NAND devices can be defined under this NAND controller.

The NAND controller might be connected to an ECC engine.

* NAND controller bindings:

Required properties:

- compatible: should be one of the following

	"atmel,at91rm9200-nand-controller"

	"atmel,at91sam9260-nand-controller"

	"atmel,at91sam9261-nand-controller"

	"atmel,at91sam9g45-nand-controller"

	"atmel,sama5d3-nand-controller"

- ranges: empty ranges property to forward EBI ranges definitions.

- #address-cells: should be set to 2.

- #size-cells: should be set to 1.

- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3

		controllers.

- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3

		  controllers.

Optional properties:

- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds

	      a PMECC engine.

* NAND device/chip bindings:

Required properties:

- reg: describes the CS lines assigned to the NAND device. If the NAND device

       exposes multiple CS lines (multi-dies chips), your reg property will

       contain X tuples of 3 entries.

       1st entry: the CS line this NAND chip is connected to

       2nd entry: the base offset of the memory region assigned to this

		  device (always 0)

       3rd entry: the memory region size (always 0x800000)

Optional properties:

- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.

- cs-gpios: the GPIO(s) used to control the CS line.

- det-gpios: the GPIO used to detect if a Smartmedia Card is present.

- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful

	    on sama5 SoCs.

All generic properties described in

Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND

device node, and NAND partitions should be defined under the NAND node as

described in Documentation/devicetree/bindings/mtd/partition.txt.

* ECC engine (PMECC) bindings:

Required properties:

- compatible: should be one of the following

	"atmel,at91sam9g45-pmecc"

	"atmel,sama5d4-pmecc"

	"atmel,sama5d2-pmecc"

- reg: should contain 2 register ranges. The first one is pointing to the PMECC

       block, and the second one to the PMECC_ERRLOC block.

Example:

	pmecc: ecc-engine@ffffc070 {

		compatible = "atmel,at91sam9g45-pmecc";

                reg = <0xffffc070 0x490>,

                      <0xffffc500 0x100>;

	};

	ebi: ebi@10000000 {

		compatible = "atmel,sama5d3-ebi";

		#address-cells = <2>;

		#size-cells = <1>;

		atmel,smc = <&hsmc>;

		reg = <0x10000000 0x10000000

		       0x40000000 0x30000000>;

		ranges = <0x0 0x0 0x10000000 0x10000000

			  0x1 0x0 0x40000000 0x10000000

			  0x2 0x0 0x50000000 0x10000000

			  0x3 0x0 0x60000000 0x10000000>;

		clocks = <&mck>;

                nand_controller: nand-controller {

			compatible = "atmel,sama5d3-nand-controller";

			atmel,nfc-sram = <&nfc_sram>;

			atmel,nfc-io = <&nfc_io>;

			ecc-engine = <&pmecc>;

			#address-cells = <2>;

			#size-cells = <1>;

			ranges;

			nand@3 {

				reg = <0x3 0x0 0x800000>;

				atmel,rb = <0>;

				/*

				 * Put generic NAND/MTD properties and

				 * subnodes here.

				 */

			};

		};

	};

-----------------------------------------------------------------------

Deprecated bindings (should not be used in new device trees):

Required properties:

- compatible: The possible values are:

* Denali NAND controller

Required properties:

  - compatible : should be "denali,denali-nand-dt"

  - compatible : should be one of the following:

      "altr,socfpga-denali-nand"            - for Altera SOCFPGA

  - reg : should contain registers location and length for data and reg.

  - reg-names: Should contain the reg names "nand_data" and "denali_reg"

  - interrupts : The interrupt number.

  - dm-mask : DMA bit mask

The device tree may optionally contain sub-nodes describing partitions of the

address space. See partition.txt for more detail.

nand: nand@ff900000 {

	#address-cells = <1>;

	#size-cells = <1>;

	compatible = "denali,denali-nand-dt";

	compatible = "altr,socfpga-denali-nand";

	reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;

	reg-names = "nand_data", "denali_reg";

	interrupts = <0 144 4>;

	dma-mask = <0xffffffff>;

};

M:	Josh Wu <rainyfeeling@outlook.com>

L:	linux-mtd@lists.infradead.org

S:	Supported

F:	drivers/mtd/nand/atmel_nand*

F:	drivers/mtd/nand/atmel/*

ATMEL SDMMC DRIVER

M:	Ludovic Desroches <ludovic.desroches@microchip.com>

	bool "NAND flash support"

	depends on ETRAX_ARCH_V32

	select MTD_NAND

	select MTD_NAND_IDS

	help

	  This option enables MTD mapping of NAND flash devices.  Needed to use

	  NAND flash memories.  If unsure, say Y.

config FSL_IFC

	bool

	depends on FSL_SOC || ARCH_LAYERSCAPE

	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A

config JZ4780_NEMC

	bool "Ingenic JZ4780 SoC NEMC driver"