Unverified Commit 5132b3d2 authored by Linus Walleij's avatar Linus Walleij Committed by Mark Brown
Browse files

spi: gpio: Support 3WIRE high-impedance turn-around 



Some devices such as the TPO TPG110 display panel require
a "high-impedance turn-around", in effect a clock cycle after
switching the line from output to input mode.

Support this in the GPIO driver to begin with. Other driver
may implement it if they can, it is unclear if this can
be achieved with anything else than GPIO bit-banging.

Cc: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: default avatarLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
parent 65102238

drivers/spi/spi-gpio.c

+21 −3
Original line number Diff line number Diff line
@@ -256,11 +256,29 @@ static int spi_gpio_setup(struct spi_device *spi) 
static int spi_gpio_set_direction(struct spi_device *spi, bool output)

{

	struct spi_gpio *spi_gpio = spi_to_spi_gpio(spi);

	int ret;



	if (output)

		return gpiod_direction_output(spi_gpio->mosi, 1);

	else

		return gpiod_direction_input(spi_gpio->mosi);



	ret = gpiod_direction_input(spi_gpio->mosi);

	if (ret)

		return ret;

	/*

	 * Send a turnaround high impedance cycle when switching

	 * from output to input. Theoretically there should be

	 * a clock delay here, but as has been noted above, the

	 * nsec delay function for bit-banged GPIO is simply

	 * {} because bit-banging just doesn't get fast enough

	 * anyway.

	 */

	if (spi->mode & SPI_3WIRE_HIZ) {

		gpiod_set_value_cansleep(spi_gpio->sck,

					 !(spi->mode & SPI_CPOL));

		gpiod_set_value_cansleep(spi_gpio->sck,

					 !!(spi->mode & SPI_CPOL));

	}

	return 0;

}



static void spi_gpio_cleanup(struct spi_device *spi)
@@ -410,7 +428,7 @@ static int spi_gpio_probe(struct platform_device *pdev) 
		return status;



	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);

	master->mode_bits = SPI_3WIRE | SPI_CPHA | SPI_CPOL;

	master->mode_bits = SPI_3WIRE | SPI_3WIRE_HIZ | SPI_CPHA | SPI_CPOL;

	master->flags = master_flags;

	master->bus_num = pdev->id;

	/* The master needs to think there is a chipselect even if not connected */

include/linux/spi/spi.h

+1 −0
Original line number Diff line number Diff line
@@ -155,6 +155,7 @@ struct spi_device { 
#define	SPI_RX_DUAL	0x400			/* receive with 2 wires */

#define	SPI_RX_QUAD	0x800			/* receive with 4 wires */

#define SPI_CS_WORD	0x1000			/* toggle cs after each word */

#define	SPI_3WIRE_HIZ	0x2000			/* high impedance turnaround */

	int			irq;

	void			*controller_state;

	void			*controller_data;

CRA Git | Maintained and supported by SUSTech CRA and CCSE