Commit 4e46c410 authored by Aidan Thornton's avatar Aidan Thornton Committed by Johan Hovold
Browse files

USB: serial: ch341: reinitialize chip on reconfiguration 



Changing the LCR register after initialization does not seem to be reliable
on all chips (particularly not on CH341A). Restructure initialization and
configuration to always reinit the chip on configuration changes instead and
pass the LCR register value directly to the initialization command.

(Note that baud rates above 500kbaud are incorrect, but they're incorrect in
the same way both before and after this patch at least on the CH340G. Fixing
this isn't a priority as higher baud rates don't seem that reliable anyway.)

Cleaned-up version of a patch by Grigori Goronzy

Signed-off-by: default avatarAidan Thornton <makosoft@gmail.com>
Reviewed-by: default avatarGrigori Goronzy <greg@chown.ath.cx>
Signed-off-by: default avatarJohan Hovold <johan@kernel.org>
parent 6fde8d29

drivers/usb/serial/ch341.c

+20 −17
Original line number Diff line number Diff line
@@ -132,10 +132,10 @@ static int ch341_control_in(struct usb_device *dev, 
	return r;

}



static int ch341_set_baudrate(struct usb_device *dev,

			      struct ch341_private *priv)

static int ch341_init_set_baudrate(struct usb_device *dev,

				   struct ch341_private *priv, unsigned ctrl)

{

	short a, b;

	short a;

	int r;

	unsigned long factor;

	short divisor;
@@ -155,11 +155,10 @@ static int ch341_set_baudrate(struct usb_device *dev, 


	factor = 0x10000 - factor;

	a = (factor & 0xff00) | divisor;

	b = factor & 0xff;



	r = ch341_control_out(dev, CH341_REQ_WRITE_REG, 0x1312, a);

	if (!r)

		r = ch341_control_out(dev, CH341_REQ_WRITE_REG, 0x0f2c, b);

	/* 0x9c is "enable SFR_UART Control register and timer" */

	r = ch341_control_out(dev, CH341_REQ_SERIAL_INIT,

			      0x9c | (ctrl << 8), a | 0x80);



	return r;

}
@@ -218,10 +217,6 @@ static int ch341_configure(struct usb_device *dev, struct ch341_private *priv) 
	if (r < 0)

		goto out;



	r = ch341_set_baudrate(dev, priv);

	if (r < 0)

		goto out;



	/* expect two bytes 0x56 0x00 */

	r = ch341_control_in(dev, CH341_REQ_READ_REG, 0x2518, 0, buffer, size);

	if (r < 0)
@@ -236,11 +231,7 @@ static int ch341_configure(struct usb_device *dev, struct ch341_private *priv) 
	if (r < 0)

		goto out;



	r = ch341_control_out(dev, CH341_REQ_SERIAL_INIT, 0x501f, 0xd90a);

	if (r < 0)

		goto out;



	r = ch341_set_baudrate(dev, priv);

	r = ch341_init_set_baudrate(dev, priv, 0);

	if (r < 0)

		goto out;
@@ -355,16 +346,28 @@ static void ch341_set_termios(struct tty_struct *tty, 
	struct ch341_private *priv = usb_get_serial_port_data(port);

	unsigned baud_rate;

	unsigned long flags;

	unsigned char ctrl;

	int r;



	/* redundant changes may cause the chip to lose bytes */

	if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios))

		return;



	baud_rate = tty_get_baud_rate(tty);



	priv->baud_rate = baud_rate;



	ctrl = CH341_LCR_ENABLE_RX | CH341_LCR_ENABLE_TX | CH341_LCR_CS8;



	if (baud_rate) {

		spin_lock_irqsave(&priv->lock, flags);

		priv->line_control |= (CH341_BIT_DTR | CH341_BIT_RTS);

		spin_unlock_irqrestore(&priv->lock, flags);

		ch341_set_baudrate(port->serial->dev, priv);

		r = ch341_init_set_baudrate(port->serial->dev, priv, ctrl);

		if (r < 0 && old_termios) {

			priv->baud_rate = tty_termios_baud_rate(old_termios);

			tty_termios_copy_hw(&tty->termios, old_termios);

		}

	} else {

		spin_lock_irqsave(&priv->lock, flags);

		priv->line_control &= ~(CH341_BIT_DTR | CH341_BIT_RTS);

CRA Git | Maintained and supported by SUSTech CRA and CCSE