arm64: dts: meson-gxbb-odroidc2: Fix node order (3b69bdbf) · Commits · 戴 / test

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

+54 −54

Original line number	Diff line number	Diff line
		@@ -137,16 +137,6 @@
		};
		};

		&scpi_clocks {
		status = "disabled";
		};

		&uart_AO {
		status = "okay";
		pinctrl-0 = <&uart_ao_a_pins>;
		pinctrl-names = "default";
		};

		&ethmac {
		status = "okay";
		pinctrl-0 = <&eth_rgmii_pins>;
		@@ -172,6 +162,33 @@
		};
		};

		&gpio_ao {
		/*
		* WARNING: The USB Hub on the Odroid-C2 needs a reset signal
		* to be turned high in order to be detected by the USB Controller
		* This signal should be handled by a USB specific power sequence
		* in order to reset the Hub when USB bus is powered down.
		*/
		usb-hub {
		gpio-hog;
		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
		output-high;
		line-name = "usb-hub-reset";
		};
		};

		&i2c_A {
		status = "okay";
		pinctrl-0 = <&i2c_a_pins>;
		pinctrl-names = "default";
		};

		&ir {
		status = "okay";
		pinctrl-0 = <&remote_input_ao_pins>;
		pinctrl-names = "default";
		};

		&pinctrl_aobus {
		gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
		"USB HUB nRESET", "USB OTG Power En",
		@@ -223,55 +240,15 @@
		"";
		};

		&ir {
		status = "okay";
		pinctrl-0 = <&remote_input_ao_pins>;
		pinctrl-names = "default";
		};

		&i2c_A {
		status = "okay";
		pinctrl-0 = <&i2c_a_pins>;
		pinctrl-names = "default";
		};

		&gpio_ao {
		/*
		* WARNING: The USB Hub on the Odroid-C2 needs a reset signal
		* to be turned high in order to be detected by the USB Controller
		* This signal should be handled by a USB specific power sequence
		* in order to reset the Hub when USB bus is powered down.
		*/
		usb-hub {
		gpio-hog;
		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
		output-high;
		line-name = "usb-hub-reset";
		};
		};

		&usb0_phy {
		status = "okay";
		phy-supply = <&usb_otg_pwr>;
		};

		&usb1_phy {
		status = "okay";
		};

		&usb0 {
		status = "okay";
		};

		&usb1 {
		status = "okay";
		};

		&saradc {
		status = "okay";
		vref-supply = <&vcc1v8>;
		};

		&scpi_clocks {
		status = "disabled";
		};

		/* SD */
		&sd_emmc_b {
		status = "okay";
		@@ -309,3 +286,26 @@
		vmmc-supply = <&vcc3v3>;
		vqmmc-supply = <&vcc1v8>;
		};

		&uart_AO {
		status = "okay";
		pinctrl-0 = <&uart_ao_a_pins>;
		pinctrl-names = "default";
		};

		&usb0_phy {
		status = "okay";
		phy-supply = <&usb_otg_pwr>;
		};

		&usb1_phy {
		status = "okay";
		};

		&usb0 {
		status = "okay";
		};

		&usb1 {
		status = "okay";
		};

Admin message