memory: brcmstb: Add driver for DPFE (2f330caf) · Commits · 戴 / test

MAINTAINERS

+8 −0

Original line number	Diff line number	Diff line
		@@ -2963,6 +2963,14 @@ L: bcm-kernel-feedback-list@broadcom.com
		S: Maintained
		F: drivers/mtd/nand/brcmnand/

		BROADCOM STB DPFE DRIVER
		M: Markus Mayer <mmayer@broadcom.com>
		M: bcm-kernel-feedback-list@broadcom.com
		L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
		S: Maintained
		F: Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.txt
		F: drivers/memory/brcmstb_dpfe.c

		BROADCOM SYSTEMPORT ETHERNET DRIVER
		M: Florian Fainelli <f.fainelli@gmail.com>
		L: netdev@vger.kernel.org

drivers/memory/Makefile

+1 −0

Original line number	Diff line number	Diff line
		@@ -8,6 +8,7 @@ endif
		obj-$(CONFIG_ARM_PL172_MPMC) += pl172.o
		obj-$(CONFIG_ATMEL_SDRAMC) += atmel-sdramc.o
		obj-$(CONFIG_ATMEL_EBI) += atmel-ebi.o
		obj-$(CONFIG_ARCH_BRCMSTB) += brcmstb_dpfe.o
		obj-$(CONFIG_TI_AEMIF) += ti-aemif.o
		obj-$(CONFIG_TI_EMIF) += emif.o
		obj-$(CONFIG_OMAP_GPMC) += omap-gpmc.o

drivers/memory/brcmstb_dpfe.c

0 → 100644

+701 −0

Original line number	Diff line number	Diff line
		/*
		* DDR PHY Front End (DPFE) driver for Broadcom set top box SoCs
		*
		* Copyright (c) 2017 Broadcom
		*
		* Released under the GPLv2 only.
		* SPDX-License-Identifier: GPL-2.0
		*/

		/*
		* This driver provides access to the DPFE interface of Broadcom STB SoCs.
		* The firmware running on the DCPU inside the DDR PHY can provide current
		* information about the system's RAM, for instance the DRAM refresh rate.
		* This can be used as an indirect indicator for the DRAM's temperature.
		* Slower refresh rate means cooler RAM, higher refresh rate means hotter
		* RAM.
		*
		* Throughout the driver, we use readl_relaxed() and writel_relaxed(), which
		* already contain the appropriate le32_to_cpu()/cpu_to_le32() calls.
		*
		* Note regarding the loading of the firmware image: we use be32_to_cpu()
		* and le_32_to_cpu(), so we can support the following four cases:
		* - LE kernel + LE firmware image (the most common case)
		* - LE kernel + BE firmware image
		* - BE kernel + LE firmware image
		* - BE kernel + BE firmware image
		*
		* The DPCU always runs in big endian mode. The firwmare image, however, can
		* be in either format. Also, communication between host CPU and DCPU is
		* always in little endian.
		*/

		#include <linux/delay.h>
		#include <linux/firmware.h>
		#include <linux/io.h>
		#include <linux/module.h>
		#include <linux/of_address.h>
		#include <linux/platform_device.h>

		#define DRVNAME "brcmstb-dpfe"
		#define FIRMWARE_NAME "dpfe.bin"

		/* DCPU register offsets */
		#define REG_DCPU_RESET 0x0
		#define REG_TO_DCPU_MBOX 0x10
		#define REG_TO_HOST_MBOX 0x14

		/* Message RAM */
		#define DCPU_MSG_RAM(x) (0x100 + (x) * sizeof(u32))

		/* DRAM Info Offsets & Masks */
		#define DRAM_INFO_INTERVAL 0x0
		#define DRAM_INFO_MR4 0x4
		#define DRAM_INFO_ERROR 0x8
		#define DRAM_INFO_MR4_MASK 0xff

		/* DRAM MR4 Offsets & Masks */
		#define DRAM_MR4_REFRESH 0x0 /* Refresh rate */
		#define DRAM_MR4_SR_ABORT 0x3 /* Self Refresh Abort */
		#define DRAM_MR4_PPRE 0x4 /* Post-package repair entry/exit */
		#define DRAM_MR4_TH_OFFS 0x5 /* Thermal Offset; vendor specific */
		#define DRAM_MR4_TUF 0x7 /* Temperature Update Flag */

		#define DRAM_MR4_REFRESH_MASK 0x7
		#define DRAM_MR4_SR_ABORT_MASK 0x1
		#define DRAM_MR4_PPRE_MASK 0x1
		#define DRAM_MR4_TH_OFFS_MASK 0x3
		#define DRAM_MR4_TUF_MASK 0x1

		/* DRAM Vendor Offsets & Masks */
		#define DRAM_VENDOR_MR5 0x0
		#define DRAM_VENDOR_MR6 0x4
		#define DRAM_VENDOR_MR7 0x8
		#define DRAM_VENDOR_MR8 0xc
		#define DRAM_VENDOR_ERROR 0x10
		#define DRAM_VENDOR_MASK 0xff

		/* Reset register bits & masks */
		#define DCPU_RESET_SHIFT 0x0
		#define DCPU_RESET_MASK 0x1
		#define DCPU_CLK_DISABLE_SHIFT 0x2

		/* DCPU return codes */
		#define DCPU_RET_ERROR_BIT BIT(31)
		#define DCPU_RET_SUCCESS 0x1
		#define DCPU_RET_ERR_HEADER (DCPU_RET_ERROR_BIT \| BIT(0))
		#define DCPU_RET_ERR_INVAL (DCPU_RET_ERROR_BIT \| BIT(1))
		#define DCPU_RET_ERR_CHKSUM (DCPU_RET_ERROR_BIT \| BIT(2))
		#define DCPU_RET_ERR_COMMAND (DCPU_RET_ERROR_BIT \| BIT(3))
		/* This error code is not firmware defined and only used in the driver. */
		#define DCPU_RET_ERR_TIMEDOUT (DCPU_RET_ERROR_BIT \| BIT(4))

		/* Firmware magic */
		#define DPFE_BE_MAGIC 0xfe1010fe
		#define DPFE_LE_MAGIC 0xfe0101fe

		/* Error codes */
		#define ERR_INVALID_MAGIC -1
		#define ERR_INVALID_SIZE -2
		#define ERR_INVALID_CHKSUM -3

		/* Message types */
		#define DPFE_MSG_TYPE_COMMAND 1
		#define DPFE_MSG_TYPE_RESPONSE 2

		#define DELAY_LOOP_MAX 200000

		enum dpfe_msg_fields {
		MSG_HEADER,
		MSG_COMMAND,
		MSG_ARG_COUNT,
		MSG_ARG0,
		MSG_CHKSUM,
		MSG_FIELD_MAX /* Last entry */
		};

		enum dpfe_commands {
		DPFE_CMD_GET_INFO,
		DPFE_CMD_GET_REFRESH,
		DPFE_CMD_GET_VENDOR,
		DPFE_CMD_MAX /* Last entry */
		};

		struct dpfe_msg {
		u32 header;
		u32 command;
		u32 arg_count;
		u32 arg0;
		u32 chksum; /* This is the sum of all other entries. */
		};

		/*
		* Format of the binary firmware file:
		*
		* entry
		* 0 header
		* value: 0xfe0101fe <== little endian
		* 0xfe1010fe <== big endian
		* 1 sequence:
		* [31:16] total segments on this build
		* [15:0] this segment sequence.
		* 2 FW version
		* 3 IMEM byte size
		* 4 DMEM byte size
		* IMEM
		* DMEM
		* last checksum ==> sum of everything
		*/
		struct dpfe_firmware_header {
		u32 magic;
		u32 sequence;
		u32 version;
		u32 imem_size;
		u32 dmem_size;
		};

		/* Things we only need during initialization. */
		struct init_data {
		unsigned int dmem_len;
		unsigned int imem_len;
		unsigned int chksum;
		bool is_big_endian;
		};

		/* Things we need for as long as we are active. */
		struct private_data {
		void __iomem *regs;
		void __iomem *dmem;
		void __iomem *imem;
		struct device *dev;
		unsigned int index;
		struct mutex lock;
		};

		static const char *error_text[] = {
		"Success", "Header code incorrect", "Unknown command or argument",
		"Incorrect checksum", "Malformed command", "Timed out",
		};

		/* List of supported firmware commands */
		static const u32 dpfe_commands[DPFE_CMD_MAX][MSG_FIELD_MAX] = {
		[DPFE_CMD_GET_INFO] = {
		[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
		[MSG_COMMAND] = 1,
		[MSG_ARG_COUNT] = 1,
		[MSG_ARG0] = 1,
		[MSG_CHKSUM] = 4,
		},
		[DPFE_CMD_GET_REFRESH] = {
		[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
		[MSG_COMMAND] = 2,
		[MSG_ARG_COUNT] = 1,
		[MSG_ARG0] = 1,
		[MSG_CHKSUM] = 5,
		},
		[DPFE_CMD_GET_VENDOR] = {
		[MSG_HEADER] = DPFE_MSG_TYPE_COMMAND,
		[MSG_COMMAND] = 2,
		[MSG_ARG_COUNT] = 1,
		[MSG_ARG0] = 2,
		[MSG_CHKSUM] = 6,
		},
		};

		static void __disable_dcpu(void __iomem *regs)
		{
		u32 val;

		/* Check if DCPU is running */
		val = readl_relaxed(regs + REG_DCPU_RESET);
		if (!(val & DCPU_RESET_MASK)) {
		/* Put DCPU in reset */
		val \|= (1 << DCPU_RESET_SHIFT);
		writel_relaxed(val, regs + REG_DCPU_RESET);
		}
		}

		static void __enable_dcpu(void __iomem *regs)
		{
		u32 val;

		/* Clear mailbox registers. */
		writel_relaxed(0, regs + REG_TO_DCPU_MBOX);
		writel_relaxed(0, regs + REG_TO_HOST_MBOX);

		/* Disable DCPU clock gating */
		val = readl_relaxed(regs + REG_DCPU_RESET);
		val &= ~(1 << DCPU_CLK_DISABLE_SHIFT);
		writel_relaxed(val, regs + REG_DCPU_RESET);

		/* Take DCPU out of reset */
		val = readl_relaxed(regs + REG_DCPU_RESET);
		val &= ~(1 << DCPU_RESET_SHIFT);
		writel_relaxed(val, regs + REG_DCPU_RESET);
		}

		static unsigned int get_msg_chksum(const u32 msg[])
		{
		unsigned int sum = 0;
		unsigned int i;

		/* Don't include the last field in the checksum. */
		for (i = 0; i < MSG_FIELD_MAX - 1; i++)
		sum += msg[i];

		return sum;
		}

		static int __send_command(struct private_data *priv, unsigned int cmd,
		u32 result[])
		{
		const u32 *msg = dpfe_commands[cmd];
		void __iomem *regs = priv->regs;
		unsigned int i, chksum;
		int ret = 0;
		u32 resp;

		if (cmd >= DPFE_CMD_MAX)
		return -1;

		mutex_lock(&priv->lock);

		/* Write command and arguments to message area */
		for (i = 0; i < MSG_FIELD_MAX; i++)
		writel_relaxed(msg[i], regs + DCPU_MSG_RAM(i));

		/* Tell DCPU there is a command waiting */
		writel_relaxed(1, regs + REG_TO_DCPU_MBOX);

		/* Wait for DCPU to process the command */
		for (i = 0; i < DELAY_LOOP_MAX; i++) {
		/* Read response code */
		resp = readl_relaxed(regs + REG_TO_HOST_MBOX);
		if (resp > 0)
		break;
		udelay(5);
		}

		if (i == DELAY_LOOP_MAX) {
		resp = (DCPU_RET_ERR_TIMEDOUT & ~DCPU_RET_ERROR_BIT);
		ret = -ffs(resp);
		} else {
		/* Read response data */
		for (i = 0; i < MSG_FIELD_MAX; i++)
		result[i] = readl_relaxed(regs + DCPU_MSG_RAM(i));
		}

		/* Tell DCPU we are done */
		writel_relaxed(0, regs + REG_TO_HOST_MBOX);

		mutex_unlock(&priv->lock);

		if (ret)
		return ret;

		/* Verify response */
		chksum = get_msg_chksum(result);
		if (chksum != result[MSG_CHKSUM])
		resp = DCPU_RET_ERR_CHKSUM;

		if (resp != DCPU_RET_SUCCESS) {
		resp &= ~DCPU_RET_ERROR_BIT;
		ret = -ffs(resp);
		}

		return ret;
		}

		/* Ensure that the firmware file loaded meets all the requirements. */
		static int __verify_firmware(struct init_data *init,
		const struct firmware *fw)
		{
		const struct dpfe_firmware_header header = (void )fw->data;
		unsigned int dmem_size, imem_size, total_size;
		bool is_big_endian = false;
		const u32 *chksum_ptr;

		if (header->magic == DPFE_BE_MAGIC)
		is_big_endian = true;
		else if (header->magic != DPFE_LE_MAGIC)
		return ERR_INVALID_MAGIC;

		if (is_big_endian) {
		dmem_size = be32_to_cpu(header->dmem_size);
		imem_size = be32_to_cpu(header->imem_size);
		} else {
		dmem_size = le32_to_cpu(header->dmem_size);
		imem_size = le32_to_cpu(header->imem_size);
		}

		/* Data and instruction sections are 32 bit words. */
		if ((dmem_size % sizeof(u32)) != 0 \|\| (imem_size % sizeof(u32)) != 0)
		return ERR_INVALID_SIZE;

		/*
		* The header + the data section + the instruction section + the
		* checksum must be equal to the total firmware size.
		*/
		total_size = dmem_size + imem_size + sizeof(*header) +
		sizeof(*chksum_ptr);
		if (total_size != fw->size)
		return ERR_INVALID_SIZE;

		/* The checksum comes at the very end. */
		chksum_ptr = (void )fw->data + sizeof(header) + dmem_size + imem_size;

		init->is_big_endian = is_big_endian;
		init->dmem_len = dmem_size;
		init->imem_len = imem_size;
		init->chksum = (is_big_endian)
		? be32_to_cpu(chksum_ptr) : le32_to_cpu(chksum_ptr);

		return 0;
		}

		/* Verify checksum by reading back the firmware from co-processor RAM. */
		static int __verify_fw_checksum(struct init_data *init,
		struct private_data *priv,
		const struct dpfe_firmware_header *header,
		u32 checksum)
		{
		u32 magic, sequence, version, sum;
		u32 __iomem *dmem = priv->dmem;
		u32 __iomem *imem = priv->imem;
		unsigned int i;

		if (init->is_big_endian) {
		magic = be32_to_cpu(header->magic);
		sequence = be32_to_cpu(header->sequence);
		version = be32_to_cpu(header->version);
		} else {
		magic = le32_to_cpu(header->magic);
		sequence = le32_to_cpu(header->sequence);
		version = le32_to_cpu(header->version);
		}

		sum = magic + sequence + version + init->dmem_len + init->imem_len;

		for (i = 0; i < init->dmem_len / sizeof(u32); i++)
		sum += readl_relaxed(dmem + i);

		for (i = 0; i < init->imem_len / sizeof(u32); i++)
		sum += readl_relaxed(imem + i);

		return (sum == checksum) ? 0 : -1;
		}

		static int __write_firmware(u32 __iomem mem, const u32 fw,
		unsigned int size, bool is_big_endian)
		{
		unsigned int i;

		/* Convert size to 32-bit words. */
		size /= sizeof(u32);

		/* It is recommended to clear the firmware area first. */
		for (i = 0; i < size; i++)
		writel_relaxed(0, mem + i);

		/* Now copy it. */
		if (is_big_endian) {
		for (i = 0; i < size; i++)
		writel_relaxed(be32_to_cpu(fw[i]), mem + i);
		} else {
		for (i = 0; i < size; i++)
		writel_relaxed(le32_to_cpu(fw[i]), mem + i);
		}

		return 0;
		}

		static int brcmstb_dpfe_download_firmware(struct platform_device *pdev,
		struct init_data *init)
		{
		const struct dpfe_firmware_header *header;
		unsigned int dmem_size, imem_size;
		struct device *dev = &pdev->dev;
		bool is_big_endian = false;
		struct private_data *priv;
		const struct firmware *fw;
		const u32 dmem, imem;
		const void *fw_blob;
		int ret;

		ret = request_firmware(&fw, FIRMWARE_NAME, dev);
		/* request_firmware() prints its own error messages. */
		if (ret)
		return ret;

		priv = platform_get_drvdata(pdev);

		ret = __verify_firmware(init, fw);
		if (ret)
		return -EFAULT;

		__disable_dcpu(priv->regs);

		is_big_endian = init->is_big_endian;
		dmem_size = init->dmem_len;
		imem_size = init->imem_len;

		/* At the beginning of the firmware blob is a header. */
		header = (struct dpfe_firmware_header *)fw->data;
		/* Void pointer to the beginning of the actual firmware. */
		fw_blob = fw->data + sizeof(*header);
		/* IMEM comes right after the header. */
		imem = fw_blob;
		/* DMEM follows after IMEM. */
		dmem = fw_blob + imem_size;

		ret = __write_firmware(priv->dmem, dmem, dmem_size, is_big_endian);
		if (ret)
		return ret;
		ret = __write_firmware(priv->imem, imem, imem_size, is_big_endian);
		if (ret)
		return ret;

		ret = __verify_fw_checksum(init, priv, header, init->chksum);
		if (ret)
		return ret;

		__enable_dcpu(priv->regs);

		return 0;
		}

		static ssize_t generic_show(unsigned int command, u32 response[],
		struct device dev, char buf)
		{
		struct private_data *priv;
		int ret;

		priv = dev_get_drvdata(dev);
		if (!priv)
		return sprintf(buf, "ERROR: driver private data not set\n");

		ret = __send_command(priv, command, response);
		if (ret < 0)
		return sprintf(buf, "ERROR: %s\n", error_text[-ret]);

		return 0;
		}

		static ssize_t show_info(struct device dev, struct device_attribute devattr,
		char *buf)
		{
		u32 response[MSG_FIELD_MAX];
		unsigned int info;
		int ret;

		ret = generic_show(DPFE_CMD_GET_INFO, response, dev, buf);
		if (ret)
		return ret;

		info = response[MSG_ARG0];

		return sprintf(buf, "%u.%u.%u.%u\n",
		(info >> 24) & 0xff,
		(info >> 16) & 0xff,
		(info >> 8) & 0xff,
		info & 0xff);
		}

		static ssize_t show_refresh(struct device *dev,
		struct device_attribute devattr, char buf)
		{
		u32 response[MSG_FIELD_MAX];
		void __iomem *info;
		struct private_data *priv;
		unsigned int offset;
		u8 refresh, sr_abort, ppre, thermal_offs, tuf;
		u32 mr4;
		int ret;

		ret = generic_show(DPFE_CMD_GET_REFRESH, response, dev, buf);
		if (ret)
		return ret;

		priv = dev_get_drvdata(dev);
		offset = response[MSG_ARG0];
		info = priv->dmem + offset;

		mr4 = readl_relaxed(info + DRAM_INFO_MR4) & DRAM_INFO_MR4_MASK;

		refresh = (mr4 >> DRAM_MR4_REFRESH) & DRAM_MR4_REFRESH_MASK;
		sr_abort = (mr4 >> DRAM_MR4_SR_ABORT) & DRAM_MR4_SR_ABORT_MASK;
		ppre = (mr4 >> DRAM_MR4_PPRE) & DRAM_MR4_PPRE_MASK;
		thermal_offs = (mr4 >> DRAM_MR4_TH_OFFS) & DRAM_MR4_TH_OFFS_MASK;
		tuf = (mr4 >> DRAM_MR4_TUF) & DRAM_MR4_TUF_MASK;

		return sprintf(buf, "%#x %#x %#x %#x %#x %#x %#x\n",
		readl_relaxed(info + DRAM_INFO_INTERVAL),
		refresh, sr_abort, ppre, thermal_offs, tuf,
		readl_relaxed(info + DRAM_INFO_ERROR));
		}

		static ssize_t store_refresh(struct device dev, struct device_attribute attr,
		const char *buf, size_t count)
		{
		u32 response[MSG_FIELD_MAX];
		struct private_data *priv;
		void __iomem *info;
		unsigned int offset;
		unsigned long val;
		int ret;

		if (kstrtoul(buf, 0, &val) < 0)
		return -EINVAL;

		priv = dev_get_drvdata(dev);

		ret = __send_command(priv, DPFE_CMD_GET_REFRESH, response);
		if (ret)
		return ret;

		offset = response[MSG_ARG0];
		info = priv->dmem + offset;
		writel_relaxed(val, info + DRAM_INFO_INTERVAL);

		return count;
		}

		static ssize_t show_vendor(struct device dev, struct device_attribute devattr,
		char *buf)
		{
		u32 response[MSG_FIELD_MAX];
		struct private_data *priv;
		void __iomem *info;
		unsigned int offset;
		int ret;

		ret = generic_show(DPFE_CMD_GET_VENDOR, response, dev, buf);
		if (ret)
		return ret;

		offset = response[MSG_ARG0];
		priv = dev_get_drvdata(dev);
		info = priv->dmem + offset;

		return sprintf(buf, "%#x %#x %#x %#x %#x\n",
		readl_relaxed(info + DRAM_VENDOR_MR5) & DRAM_VENDOR_MASK,
		readl_relaxed(info + DRAM_VENDOR_MR6) & DRAM_VENDOR_MASK,
		readl_relaxed(info + DRAM_VENDOR_MR7) & DRAM_VENDOR_MASK,
		readl_relaxed(info + DRAM_VENDOR_MR8) & DRAM_VENDOR_MASK,
		readl_relaxed(info + DRAM_VENDOR_ERROR));
		}

		static int brcmstb_dpfe_resume(struct platform_device *pdev)
		{
		struct init_data init;

		return brcmstb_dpfe_download_firmware(pdev, &init);
		}

		static DEVICE_ATTR(dpfe_info, 0444, show_info, NULL);
		static DEVICE_ATTR(dpfe_refresh, 0644, show_refresh, store_refresh);
		static DEVICE_ATTR(dpfe_vendor, 0444, show_vendor, NULL);
		static struct attribute *dpfe_attrs[] = {
		&dev_attr_dpfe_info.attr,
		&dev_attr_dpfe_refresh.attr,
		&dev_attr_dpfe_vendor.attr,
		NULL
		};
		ATTRIBUTE_GROUPS(dpfe);

		static int brcmstb_dpfe_probe(struct platform_device *pdev)
		{
		struct device *dev = &pdev->dev;
		struct private_data *priv;
		struct device *dpfe_dev;
		struct init_data init;
		struct resource *res;
		u32 index;
		int ret;

		priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
		if (!priv)
		return -ENOMEM;

		mutex_init(&priv->lock);
		platform_set_drvdata(pdev, priv);

		/* Cell index is optional; default to 0 if not present. */
		ret = of_property_read_u32(dev->of_node, "cell-index", &index);
		if (ret)
		index = 0;

		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dpfe-cpu");
		priv->regs = devm_ioremap_resource(dev, res);
		if (IS_ERR(priv->regs)) {
		dev_err(dev, "couldn't map DCPU registers\n");
		return -ENODEV;
		}

		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dpfe-dmem");
		priv->dmem = devm_ioremap_resource(dev, res);
		if (IS_ERR(priv->dmem)) {
		dev_err(dev, "Couldn't map DCPU data memory\n");
		return -ENOENT;
		}

		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dpfe-imem");
		priv->imem = devm_ioremap_resource(dev, res);
		if (IS_ERR(priv->imem)) {
		dev_err(dev, "Couldn't map DCPU instruction memory\n");
		return -ENOENT;
		}

		ret = brcmstb_dpfe_download_firmware(pdev, &init);
		if (ret)
		goto err;

		dpfe_dev = devm_kzalloc(dev, sizeof(*dpfe_dev), GFP_KERNEL);
		if (!dpfe_dev) {
		ret = -ENOMEM;
		goto err;
		}

		priv->dev = dpfe_dev;
		priv->index = index;

		dpfe_dev->parent = dev;
		dpfe_dev->groups = dpfe_groups;
		dpfe_dev->of_node = dev->of_node;
		dev_set_drvdata(dpfe_dev, priv);
		dev_set_name(dpfe_dev, "dpfe%u", index);

		ret = device_register(dpfe_dev);
		if (ret)
		goto err;

		dev_info(dev, "registered.\n");

		return 0;

		err:
		dev_err(dev, "failed to initialize -- error %d\n", ret);

		return ret;
		}

		static const struct of_device_id brcmstb_dpfe_of_match[] = {
		{ .compatible = "brcm,dpfe-cpu", },
		{}
		};
		MODULE_DEVICE_TABLE(of, brcmstb_dpfe_of_match);

		static struct platform_driver brcmstb_dpfe_driver = {
		.driver = {
		.name = DRVNAME,
		.of_match_table = brcmstb_dpfe_of_match,
		},
		.probe = brcmstb_dpfe_probe,
		.resume = brcmstb_dpfe_resume,
		};

		module_platform_driver(brcmstb_dpfe_driver);

		MODULE_AUTHOR("Markus Mayer <mmayer@broadcom.com>");
		MODULE_DESCRIPTION("BRCMSTB DDR PHY Front End Driver");
		MODULE_LICENSE("GPL");

Admin message