i2c: New-style EEPROM driver using device IDs (2b7a5056) · Commits · 戴 / test

drivers/i2c/chips/Kconfig

+26 −0

Original line number	Diff line number	Diff line
		@@ -14,6 +14,32 @@ config DS1682
		This driver can also be built as a module. If so, the module
		will be called ds1682.

		config AT24
		tristate "EEPROMs from most vendors"
		depends on SYSFS && EXPERIMENTAL
		help
		Enable this driver to get read/write support to most I2C EEPROMs,
		after you configure the driver to know about each EEPROM on
		your target board. Use these generic chip names, instead of
		vendor-specific ones like at24c64 or 24lc02:

		24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
		24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024

		Unless you like data loss puzzles, always be sure that any chip
		you configure as a 24c32 (32 kbit) or larger is NOT really a
		24c16 (16 kbit) or smaller, and vice versa. Marking the chip
		as read-only won't help recover from this. Also, if your chip
		has any software write-protect mechanism you may want to review the
		code to make sure this driver won't turn it on by accident.

		If you use this with an SMBus adapter instead of an I2C adapter,
		full functionality is not available. Only smaller devices are
		supported (24c16 and below, max 4 kByte).

		This driver can also be built as a module. If so, the module
		will be called at24.

		config SENSORS_EEPROM
		tristate "EEPROM reader"
		depends on EXPERIMENTAL

drivers/i2c/chips/Makefile

+1 −0

Original line number	Diff line number	Diff line
		@@ -10,6 +10,7 @@
		#

		obj-$(CONFIG_DS1682) += ds1682.o
		obj-$(CONFIG_AT24) += at24.o
		obj-$(CONFIG_SENSORS_EEPROM) += eeprom.o
		obj-$(CONFIG_SENSORS_MAX6875) += max6875.o
		obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o

drivers/i2c/chips/at24.c

0 → 100644

+583 −0

Original line number	Diff line number	Diff line
		/*
		* at24.c - handle most I2C EEPROMs
		*
		* Copyright (C) 2005-2007 David Brownell
		* Copyright (C) 2008 Wolfram Sang, Pengutronix
		*
		* This program is free software; you can redistribute it and/or modify
		* it under the terms of the GNU General Public License as published by
		* the Free Software Foundation; either version 2 of the License, or
		* (at your option) any later version.
		*/
		#include <linux/kernel.h>
		#include <linux/init.h>
		#include <linux/module.h>
		#include <linux/slab.h>
		#include <linux/delay.h>
		#include <linux/mutex.h>
		#include <linux/sysfs.h>
		#include <linux/mod_devicetable.h>
		#include <linux/log2.h>
		#include <linux/bitops.h>
		#include <linux/jiffies.h>
		#include <linux/i2c.h>
		#include <linux/i2c/at24.h>

		/*
		* I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
		* Differences between different vendor product lines (like Atmel AT24C or
		* MicroChip 24LC, etc) won't much matter for typical read/write access.
		* There are also I2C RAM chips, likewise interchangeable. One example
		* would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes).
		*
		* However, misconfiguration can lose data. "Set 16-bit memory address"
		* to a part with 8-bit addressing will overwrite data. Writing with too
		* big a page size also loses data. And it's not safe to assume that the
		* conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC
		* uses 0x51, for just one example.
		*
		* Accordingly, explicit board-specific configuration data should be used
		* in almost all cases. (One partial exception is an SMBus used to access
		* "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.)
		*
		* So this driver uses "new style" I2C driver binding, expecting to be
		* told what devices exist. That may be in arch/X/mach-Y/board-Z.c or
		* similar kernel-resident tables; or, configuration data coming from
		* a bootloader.
		*
		* Other than binding model, current differences from "eeprom" driver are
		* that this one handles write access and isn't restricted to 24c02 devices.
		* It also handles larger devices (32 kbit and up) with two-byte addresses,
		* which won't work on pure SMBus systems.
		*/

		struct at24_data {
		struct at24_platform_data chip;
		bool use_smbus;

		/*
		* Lock protects against activities from other Linux tasks,
		* but not from changes by other I2C masters.
		*/
		struct mutex lock;
		struct bin_attribute bin;

		u8 *writebuf;
		unsigned write_max;
		unsigned num_addresses;

		/*
		* Some chips tie up multiple I2C addresses; dummy devices reserve
		* them for us, and we'll use them with SMBus calls.
		*/
		struct i2c_client *client[];
		};

		/*
		* This parameter is to help this driver avoid blocking other drivers out
		* of I2C for potentially troublesome amounts of time. With a 100 kHz I2C
		* clock, one 256 byte read takes about 1/43 second which is excessive;
		* but the 1/170 second it takes at 400 kHz may be quite reasonable; and
		* at 1 MHz (Fm+) a 1/430 second delay could easily be invisible.
		*
		* This value is forced to be a power of two so that writes align on pages.
		*/
		static unsigned io_limit = 128;
		module_param(io_limit, uint, 0);
		MODULE_PARM_DESC(io_limit, "Maximum bytes per I/O (default 128)");

		/*
		* Specs often allow 5 msec for a page write, sometimes 20 msec;
		* it's important to recover from write timeouts.
		*/
		static unsigned write_timeout = 25;
		module_param(write_timeout, uint, 0);
		MODULE_PARM_DESC(write_timeout, "Time (in ms) to try writes (default 25)");

		#define AT24_SIZE_BYTELEN 5
		#define AT24_SIZE_FLAGS 8

		#define AT24_BITMASK(x) (BIT(x) - 1)

		/* create non-zero magic value for given eeprom parameters */
		#define AT24_DEVICE_MAGIC(_len, _flags) \
		((1 << AT24_SIZE_FLAGS \| (_flags)) \
		<< AT24_SIZE_BYTELEN \| ilog2(_len))

		static const struct i2c_device_id at24_ids[] = {
		/* needs 8 addresses as A0-A2 are ignored */
		{ "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) },
		/* old variants can't be handled with this generic entry! */
		{ "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) },
		{ "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) },
		/* spd is a 24c02 in memory DIMMs */
		{ "spd", AT24_DEVICE_MAGIC(2048 / 8,
		AT24_FLAG_READONLY \| AT24_FLAG_IRUGO) },
		{ "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) },
		/* 24rf08 quirk is handled at i2c-core */
		{ "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) },
		{ "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) },
		{ "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) },
		{ "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) },
		{ "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) },
		{ "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) },
		{ "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) },
		{ "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) },
		{ "at24", 0 },
		{ /* END OF LIST */ }
		};
		MODULE_DEVICE_TABLE(i2c, at24_ids);

		/-------------------------------------------------------------------------/

		/*
		* This routine supports chips which consume multiple I2C addresses. It
		* computes the addressing information to be used for a given r/w request.
		* Assumes that sanity checks for offset happened at sysfs-layer.
		*/
		static struct i2c_client at24_translate_offset(struct at24_data at24,
		unsigned *offset)
		{
		unsigned i;

		if (at24->chip.flags & AT24_FLAG_ADDR16) {
		i = *offset >> 16;
		*offset &= 0xffff;
		} else {
		i = *offset >> 8;
		*offset &= 0xff;
		}

		return at24->client[i];
		}

		static ssize_t at24_eeprom_read(struct at24_data at24, char buf,
		unsigned offset, size_t count)
		{
		struct i2c_msg msg[2];
		u8 msgbuf[2];
		struct i2c_client *client;
		int status, i;

		memset(msg, 0, sizeof(msg));

		/*
		* REVISIT some multi-address chips don't rollover page reads to
		* the next slave address, so we may need to truncate the count.
		* Those chips might need another quirk flag.
		*
		* If the real hardware used four adjacent 24c02 chips and that
		* were misconfigured as one 24c08, that would be a similar effect:
		* one "eeprom" file not four, but larger reads would fail when
		* they crossed certain pages.
		*/

		/*
		* Slave address and byte offset derive from the offset. Always
		* set the byte address; on a multi-master board, another master
		* may have changed the chip's "current" address pointer.
		*/
		client = at24_translate_offset(at24, &offset);

		if (count > io_limit)
		count = io_limit;

		/* Smaller eeproms can work given some SMBus extension calls */
		if (at24->use_smbus) {
		if (count > I2C_SMBUS_BLOCK_MAX)
		count = I2C_SMBUS_BLOCK_MAX;
		status = i2c_smbus_read_i2c_block_data(client, offset,
		count, buf);
		dev_dbg(&client->dev, "smbus read %zd@%d --> %d\n",
		count, offset, status);
		return (status < 0) ? -EIO : status;
		}

		/*
		* When we have a better choice than SMBus calls, use a combined
		* I2C message. Write address; then read up to io_limit data bytes.
		* Note that read page rollover helps us here (unlike writes).
		* msgbuf is u8 and will cast to our needs.
		*/
		i = 0;
		if (at24->chip.flags & AT24_FLAG_ADDR16)
		msgbuf[i++] = offset >> 8;
		msgbuf[i++] = offset;

		msg[0].addr = client->addr;
		msg[0].buf = msgbuf;
		msg[0].len = i;

		msg[1].addr = client->addr;
		msg[1].flags = I2C_M_RD;
		msg[1].buf = buf;
		msg[1].len = count;

		status = i2c_transfer(client->adapter, msg, 2);
		dev_dbg(&client->dev, "i2c read %zd@%d --> %d\n",
		count, offset, status);

		if (status == 2)
		return count;
		else if (status >= 0)
		return -EIO;
		else
		return status;
		}

		static ssize_t at24_bin_read(struct kobject kobj, struct bin_attribute attr,
		char *buf, loff_t off, size_t count)
		{
		struct at24_data *at24;
		ssize_t retval = 0;

		at24 = dev_get_drvdata(container_of(kobj, struct device, kobj));

		if (unlikely(!count))
		return count;

		/*
		* Read data from chip, protecting against concurrent updates
		* from this host, but not from other I2C masters.
		*/
		mutex_lock(&at24->lock);

		while (count) {
		ssize_t status;

		status = at24_eeprom_read(at24, buf, off, count);
		if (status <= 0) {
		if (retval == 0)
		retval = status;
		break;
		}
		buf += status;
		off += status;
		count -= status;
		retval += status;
		}

		mutex_unlock(&at24->lock);

		return retval;
		}


		/*
		* REVISIT: export at24_bin{read,write}() to let other kernel code use
		* eeprom data. For example, it might hold a board's Ethernet address, or
		* board-specific calibration data generated on the manufacturing floor.
		*/


		/*
		* Note that if the hardware write-protect pin is pulled high, the whole
		* chip is normally write protected. But there are plenty of product
		* variants here, including OTP fuses and partial chip protect.
		*
		* We only use page mode writes; the alternative is sloooow. This routine
		* writes at most one page.
		*/
		static ssize_t at24_eeprom_write(struct at24_data at24, char buf,
		unsigned offset, size_t count)
		{
		struct i2c_client *client;
		struct i2c_msg msg;
		ssize_t status;
		unsigned long timeout, write_time;
		unsigned next_page;

		/* Get corresponding I2C address and adjust offset */
		client = at24_translate_offset(at24, &offset);

		/* write_max is at most a page */
		if (count > at24->write_max)
		count = at24->write_max;

		/* Never roll over backwards, to the start of this page */
		next_page = roundup(offset + 1, at24->chip.page_size);
		if (offset + count > next_page)
		count = next_page - offset;

		/* If we'll use I2C calls for I/O, set up the message */
		if (!at24->use_smbus) {
		int i = 0;

		msg.addr = client->addr;
		msg.flags = 0;

		/* msg.buf is u8 and casts will mask the values */
		msg.buf = at24->writebuf;
		if (at24->chip.flags & AT24_FLAG_ADDR16)
		msg.buf[i++] = offset >> 8;

		msg.buf[i++] = offset;
		memcpy(&msg.buf[i], buf, count);
		msg.len = i + count;
		}

		/*
		* Writes fail if the previous one didn't complete yet. We may
		* loop a few times until this one succeeds, waiting at least
		* long enough for one entire page write to work.
		*/
		timeout = jiffies + msecs_to_jiffies(write_timeout);
		do {
		write_time = jiffies;
		if (at24->use_smbus) {
		status = i2c_smbus_write_i2c_block_data(client,
		offset, count, buf);
		if (status == 0)
		status = count;
		} else {
		status = i2c_transfer(client->adapter, &msg, 1);
		if (status == 1)
		status = count;
		}
		dev_dbg(&client->dev, "write %zd@%d --> %zd (%ld)\n",
		count, offset, status, jiffies);

		if (status == count)
		return count;

		/* REVISIT: at HZ=100, this is sloooow */
		msleep(1);
		} while (time_before(write_time, timeout));

		return -ETIMEDOUT;
		}

		static ssize_t at24_bin_write(struct kobject kobj, struct bin_attribute attr,
		char *buf, loff_t off, size_t count)
		{
		struct at24_data *at24;
		ssize_t retval = 0;

		at24 = dev_get_drvdata(container_of(kobj, struct device, kobj));

		if (unlikely(!count))
		return count;

		/*
		* Write data to chip, protecting against concurrent updates
		* from this host, but not from other I2C masters.
		*/
		mutex_lock(&at24->lock);

		while (count) {
		ssize_t status;

		status = at24_eeprom_write(at24, buf, off, count);
		if (status <= 0) {
		if (retval == 0)
		retval = status;
		break;
		}
		buf += status;
		off += status;
		count -= status;
		retval += status;
		}

		mutex_unlock(&at24->lock);

		return retval;
		}

		/-------------------------------------------------------------------------/

		static int at24_probe(struct i2c_client client, const struct i2c_device_id id)
		{
		struct at24_platform_data chip;
		bool writable;
		bool use_smbus = false;
		struct at24_data *at24;
		int err;
		unsigned i, num_addresses;
		kernel_ulong_t magic;

		if (client->dev.platform_data) {
		chip = (struct at24_platform_data )client->dev.platform_data;
		} else {
		if (!id->driver_data) {
		err = -ENODEV;
		goto err_out;
		}
		magic = id->driver_data;
		chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN));
		magic >>= AT24_SIZE_BYTELEN;
		chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS);
		/*
		* This is slow, but we can't know all eeproms, so we better
		* play safe. Specifying custom eeprom-types via platform_data
		* is recommended anyhow.
		*/
		chip.page_size = 1;
		}

		if (!is_power_of_2(chip.byte_len))
		dev_warn(&client->dev,
		"byte_len looks suspicious (no power of 2)!\n");
		if (!is_power_of_2(chip.page_size))
		dev_warn(&client->dev,
		"page_size looks suspicious (no power of 2)!\n");

		/* Use I2C operations unless we're stuck with SMBus extensions. */
		if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
		if (chip.flags & AT24_FLAG_ADDR16) {
		err = -EPFNOSUPPORT;
		goto err_out;
		}
		if (!i2c_check_functionality(client->adapter,
		I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
		err = -EPFNOSUPPORT;
		goto err_out;
		}
		use_smbus = true;
		}

		if (chip.flags & AT24_FLAG_TAKE8ADDR)
		num_addresses = 8;
		else
		num_addresses = DIV_ROUND_UP(chip.byte_len,
		(chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256);

		at24 = kzalloc(sizeof(struct at24_data) +
		num_addresses * sizeof(struct i2c_client *), GFP_KERNEL);
		if (!at24) {
		err = -ENOMEM;
		goto err_out;
		}

		mutex_init(&at24->lock);
		at24->use_smbus = use_smbus;
		at24->chip = chip;
		at24->num_addresses = num_addresses;

		/*
		* Export the EEPROM bytes through sysfs, since that's convenient.
		* By default, only root should see the data (maybe passwords etc)
		*/
		at24->bin.attr.name = "eeprom";
		at24->bin.attr.mode = chip.flags & AT24_FLAG_IRUGO ? S_IRUGO : S_IRUSR;
		at24->bin.attr.owner = THIS_MODULE;
		at24->bin.read = at24_bin_read;
		at24->bin.size = chip.byte_len;

		writable = !(chip.flags & AT24_FLAG_READONLY);
		if (writable) {
		if (!use_smbus \|\| i2c_check_functionality(client->adapter,
		I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {

		unsigned write_max = chip.page_size;

		at24->bin.write = at24_bin_write;
		at24->bin.attr.mode \|= S_IWUSR;

		if (write_max > io_limit)
		write_max = io_limit;
		if (use_smbus && write_max > I2C_SMBUS_BLOCK_MAX)
		write_max = I2C_SMBUS_BLOCK_MAX;
		at24->write_max = write_max;

		/* buffer (data + address at the beginning) */
		at24->writebuf = kmalloc(write_max + 2, GFP_KERNEL);
		if (!at24->writebuf) {
		err = -ENOMEM;
		goto err_struct;
		}
		} else {
		dev_warn(&client->dev,
		"cannot write due to controller restrictions.");
		}
		}

		at24->client[0] = client;

		/* use dummy devices for multiple-address chips */
		for (i = 1; i < num_addresses; i++) {
		at24->client[i] = i2c_new_dummy(client->adapter,
		client->addr + i);
		if (!at24->client[i]) {
		dev_err(&client->dev, "address 0x%02x unavailable\n",
		client->addr + i);
		err = -EADDRINUSE;
		goto err_clients;
		}
		}

		err = sysfs_create_bin_file(&client->dev.kobj, &at24->bin);
		if (err)
		goto err_clients;

		i2c_set_clientdata(client, at24);

		dev_info(&client->dev, "%Zd byte %s EEPROM %s\n",
		at24->bin.size, client->name,
		writable ? "(writable)" : "(read-only)");
		dev_dbg(&client->dev,
		"page_size %d, num_addresses %d, write_max %d%s\n",
		chip.page_size, num_addresses,
		at24->write_max,
		use_smbus ? ", use_smbus" : "");

		return 0;

		err_clients:
		for (i = 1; i < num_addresses; i++)
		if (at24->client[i])
		i2c_unregister_device(at24->client[i]);

		kfree(at24->writebuf);
		err_struct:
		kfree(at24);
		err_out:
		dev_dbg(&client->dev, "probe error %d\n", err);
		return err;
		}

		static int __devexit at24_remove(struct i2c_client *client)
		{
		struct at24_data *at24;
		int i;

		at24 = i2c_get_clientdata(client);
		sysfs_remove_bin_file(&client->dev.kobj, &at24->bin);

		for (i = 1; i < at24->num_addresses; i++)
		i2c_unregister_device(at24->client[i]);

		kfree(at24->writebuf);
		kfree(at24);
		i2c_set_clientdata(client, NULL);
		return 0;
		}

		/-------------------------------------------------------------------------/

		static struct i2c_driver at24_driver = {
		.driver = {
		.name = "at24",
		.owner = THIS_MODULE,
		},
		.probe = at24_probe,
		.remove = __devexit_p(at24_remove),
		.id_table = at24_ids,
		};

		static int __init at24_init(void)
		{
		io_limit = rounddown_pow_of_two(io_limit);
		return i2c_add_driver(&at24_driver);
		}
		module_init(at24_init);

		static void __exit at24_exit(void)
		{
		i2c_del_driver(&at24_driver);
		}
		module_exit(at24_exit);

		MODULE_DESCRIPTION("Driver for most I2C EEPROMs");
		MODULE_AUTHOR("David Brownell and Wolfram Sang");
		MODULE_LICENSE("GPL");

include/linux/i2c/at24.h

0 → 100644

+28 −0

Original line number	Diff line number	Diff line
		#ifndef _LINUX_AT24_H
		#define _LINUX_AT24_H

		#include <linux/types.h>

		/*
		* As seen through Linux I2C, differences between the most common types of I2C
		* memory include:
		* - How much memory is available (usually specified in bit)?
		* - What write page size does it support?
		* - Special flags (16 bit addresses, read_only, world readable...)?
		*
		* If you set up a custom eeprom type, please double-check the parameters.
		* Especially page_size needs extra care, as you risk data loss if your value
		* is bigger than what the chip actually supports!
		*/

		struct at24_platform_data {
		u32 byte_len; /* size (sum of all addr) */
		u16 page_size; /* for writes */
		u8 flags;
		#define AT24_FLAG_ADDR16 0x80 /* address pointer is 16 bit */
		#define AT24_FLAG_READONLY 0x40 /* sysfs-entry will be read-only */
		#define AT24_FLAG_IRUGO 0x20 /* sysfs-entry will be world-readable */
		#define AT24_FLAG_TAKE8ADDR 0x10 /* take always 8 addresses (24c00) */
		};

		#endif /* _LINUX_AT24_H */

Admin message