ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board (28ff811f) · Commits · 戴 / test

arch/arm/boot/dts/Makefile

+1 −0

Original line number	Diff line number	Diff line
		@@ -1091,6 +1091,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
		sun8i-h3-orangepi-plus.dtb \
		sun8i-h3-orangepi-plus2e.dtb \
		sun8i-h3-orangepi-zero-plus2.dtb \
		sun8i-h3-rervision-dvk.dtb \
		sun8i-r16-bananapi-m2m.dtb \
		sun8i-r16-nintendo-nes-classic.dtb \
		sun8i-r16-nintendo-super-nes-classic.dtb \

0 → 100644

+114 −0

Original line number	Diff line number	Diff line
		// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
		/*
		* Copyright (C) 2019 Bootlin
		* Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
		*/

		/dts-v1/;
		#include "sun8i-h3.dtsi"
		#include "sunxi-common-regulators.dtsi"

		#include <dt-bindings/gpio/gpio.h>
		#include <dt-bindings/input/input.h>

		/ {
		model = "RerVision H3-DVK";
		compatible = "rervision,h3-dvk", "allwinner,sun8i-h3";

		aliases {
		ethernet0 = &emac;
		serial0 = &uart0;
		};

		chosen {
		stdout-path = "serial0:115200n8";
		};

		connector {
		compatible = "hdmi-connector";
		type = "a";

		port {
		hdmi_con_in: endpoint {
		remote-endpoint = <&hdmi_out_con>;
		};
		};
		};
		};

		&de {
		status = "okay";
		};

		&ehci1 {
		status = "okay";
		};

		&ehci2 {
		status = "okay";
		};

		&ehci3 {
		status = "okay";
		};

		&emac {
		phy-handle = <&int_mii_phy>;
		phy-mode = "mii";
		allwinner,leds-active-low;
		status = "okay";
		};

		&hdmi {
		status = "okay";
		};

		&hdmi_out {
		hdmi_out_con: endpoint {
		remote-endpoint = <&hdmi_con_in>;
		};
		};

		&mmc0 {
		bus-width = <4>;
		cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
		status = "okay";
		vmmc-supply = <&reg_vcc3v3>;
		};

		&mmc2 {
		pinctrl-names = "default";
		pinctrl-0 = <&mmc2_8bit_pins>;
		vmmc-supply = <&reg_vcc3v3>;
		bus-width = <8>;
		non-removable;
		cap-mmc-hw-reset;
		status = "okay";
		};

		&ohci1 {
		status = "okay";
		};

		&ohci2 {
		status = "okay";
		};

		&ohci3 {
		status = "okay";
		};

		&uart0 {
		pinctrl-names = "default";
		pinctrl-0 = <&uart0_pins_a>;
		status = "okay";
		};

		&usb_otg {
		status = "okay";
		dr_mode = "peripheral";
		};

		&usbphy {
		status = "okay";
		};