spi kerneldoc update (2604288f) · Commits · 戴 / test

include/linux/spi/spi.h

+57 −1

Original line number	Diff line number	Diff line
		@@ -139,6 +139,32 @@ struct spi_message;



		/**
		* struct spi_driver - Host side "protocol" driver
		* @probe: Binds this driver to the spi device. Drivers can verify
		* that the device is actually present, and may need to configure
		* characteristics (such as bits_per_word) which weren't needed for
		* the initial configuration done during system setup.
		* @remove: Unbinds this driver from the spi device
		* @shutdown: Standard shutdown callback used during system state
		* transitions such as powerdown/halt and kexec
		* @suspend: Standard suspend callback used during system state transitions
		* @resume: Standard resume callback used during system state transitions
		* @driver: SPI device drivers should initialize the name and owner
		* field of this structure.
		*
		* This represents the kind of device driver that uses SPI messages to
		* interact with the hardware at the other end of a SPI link. It's called
		* a "protocol" driver because it works through messages rather than talking
		* directly to SPI hardware (which is what the underlying SPI controller
		* driver does to pass those messages). These protocols are defined in the
		* specification for the device(s) supported by the driver.
		*
		* As a rule, those device protocols represent the lowest level interface
		* supported by a driver, and it will support upper level interfaces too.
		* Examples of such upper levels include frameworks like MTD, networking,
		* MMC, RTC, filesystem character device nodes, and hardware monitoring.
		*/
		struct spi_driver {
		int (probe)(struct spi_device spi);
		int (remove)(struct spi_device spi);
		@@ -668,7 +694,37 @@ static inline ssize_t spi_w8r16(struct spi_device *spi, u8 cmd)
		* parport adapters, or microcontrollers acting as USB-to-SPI bridges.
		*/

		/* board-specific information about each SPI device */
		/**
		* struct spi_board_info - board-specific template for a SPI device
		* @modalias: Initializes spi_device.modalias; identifies the driver.
		* @platform_data: Initializes spi_device.platform_data; the particular
		* data stored there is driver-specific.
		* @controller_data: Initializes spi_device.controller_data; some
		* controllers need hints about hardware setup, e.g. for DMA.
		* @irq: Initializes spi_device.irq; depends on how the board is wired.
		* @max_speed_hz: Initializes spi_device.max_speed_hz; based on limits
		* from the chip datasheet and board-specific signal quality issues.
		* @bus_num: Identifies which spi_master parents the spi_device; unused
		* by spi_new_device(), and otherwise depends on board wiring.
		* @chip_select: Initializes spi_device.chip_select; depends on how
		* the board is wired.
		* @mode: Initializes spi_device.mode; based on the chip datasheet, board
		* wiring (some devices support both 3WIRE and standard modes), and
		* possibly presence of an inverter in the chipselect path.
		*
		* When adding new SPI devices to the device tree, these structures serve
		* as a partial device template. They hold information which can't always
		* be determined by drivers. Information that probe() can establish (such
		* as the default transfer wordsize) is not included here.
		*
		* These structures are used in two places. Their primary role is to
		* be stored in tables of board-specific device descriptors, which are
		* declared early in board initialization and then used (much later) to
		* populate a controller's device tree after the that controller's driver
		* initializes. A secondary (and atypical) role is as a parameter to
		* spi_new_device() call, which happens after those controller drivers
		* are active in some dynamic board configuration models.
		*/
		struct spi_board_info {
		/* the device name and module name are coupled, like platform_bus;
		* "modalias" is normally the driver name.

Admin message