Commit 241d89fc authored by Jon Arne Jørgensen's avatar Jon Arne Jørgensen Committed by Mauro Carvalho Chehab
Browse files

[media] saa7115: Add register setup and config for gm7113c 



The gm7113c chip is similar to the original saa7113 chip, so I try to
re-use most of the saa7113 specific setup-/configuration registers.
According to the datasheet, the gm7113c chip has not implemented
any register-addresses after 0x1f, so I add a new entry to for the chip
to the saa711x_has_reg function.
The devices I've seen using this chip will fail to get stable video-sync
if these registers are not zeroed:
	R_14_ANAL_ADC_COMPAT_CNTL
	R_15_VGATE_START_FID_CHG
	R_16_VGATE_STOP
	R_17_MISC_VGATE_CONF_AND_MSB
The saa711x_set_v4lstd is updated to send a simpler configuration-table
to avoid setting these registers.

Signed-off-by: default avatarJon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: default avatarEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: default avatarHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@redhat.com>
parent b11460b0

drivers/media/i2c/saa7115.c

+37 −10
Original line number Diff line number Diff line
@@ -127,6 +127,8 @@ static int saa711x_has_reg(const int id, const u8 reg) 
		return 0;



	switch (id) {

	case V4L2_IDENT_GM7113C:

		return reg != 0x14 && (reg < 0x18 || reg > 0x1e) && reg < 0x20;

	case V4L2_IDENT_SAA7113:

		return reg != 0x14 && (reg < 0x18 || reg > 0x1e) && (reg < 0x20 || reg > 0x3f) &&

		       reg != 0x5d && reg < 0x63;
@@ -214,7 +216,10 @@ static const unsigned char saa7111_init[] = { 
	0x00, 0x00

};



/* SAA7113 init codes */

/* SAA7113/GM7113C init codes

 * It's important that R_14... R_17 == 0x00

 * for the gm7113c chip to deliver stable video

 */

static const unsigned char saa7113_init[] = {

	R_01_INC_DELAY, 0x08,

	R_02_INPUT_CNTL_1, 0xc2,
@@ -448,6 +453,24 @@ static const unsigned char saa7115_cfg_50hz_video[] = { 


/* ============== SAA7715 VIDEO templates (end) =======  */



/* ============== GM7113C VIDEO templates =============  */

static const unsigned char gm7113c_cfg_60hz_video[] = {

	R_08_SYNC_CNTL, 0x68,			/* 0xBO: auto detection, 0x68 = NTSC */

	R_0E_CHROMA_CNTL_1, 0x07,		/* video autodetection is on */



	0x00, 0x00

};



static const unsigned char gm7113c_cfg_50hz_video[] = {

	R_08_SYNC_CNTL, 0x28,			/* 0x28 = PAL */

	R_0E_CHROMA_CNTL_1, 0x07,



	0x00, 0x00

};



/* ============== GM7113C VIDEO templates (end) =======  */





static const unsigned char saa7115_cfg_vbi_on[] = {

	R_80_GLOBAL_CNTL_1, 0x00,			/* reset tasks */

	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,		/* reset scaler */
@@ -932,10 +955,16 @@ static void saa711x_set_v4lstd(struct v4l2_subdev *sd, v4l2_std_id std) 
	// This works for NTSC-M, SECAM-L and the 50Hz PAL variants.

	if (std & V4L2_STD_525_60) {

		v4l2_dbg(1, debug, sd, "decoder set standard 60 Hz\n");

		if (state->ident == V4L2_IDENT_GM7113C)

			saa711x_writeregs(sd, gm7113c_cfg_60hz_video);

		else

			saa711x_writeregs(sd, saa7115_cfg_60hz_video);

		saa711x_set_size(sd, 720, 480);

	} else {

		v4l2_dbg(1, debug, sd, "decoder set standard 50 Hz\n");

		if (state->ident == V4L2_IDENT_GM7113C)

			saa711x_writeregs(sd, gm7113c_cfg_50hz_video);

		else

			saa711x_writeregs(sd, saa7115_cfg_50hz_video);

		saa711x_set_size(sd, 720, 576);

	}
@@ -949,7 +978,8 @@ static void saa711x_set_v4lstd(struct v4l2_subdev *sd, v4l2_std_id std) 
	011 NTSC N (3.58MHz)            PAL M (3.58MHz)

	100 reserved                    NTSC-Japan (3.58MHz)

	*/

	if (state->ident <= V4L2_IDENT_SAA7113) {

	if (state->ident <= V4L2_IDENT_SAA7113 ||

	    state->ident == V4L2_IDENT_GM7113C) {

		u8 reg = saa711x_read(sd, R_0E_CHROMA_CNTL_1) & 0x8f;



		if (std == V4L2_STD_PAL_M) {
@@ -1220,7 +1250,8 @@ static int saa711x_s_routing(struct v4l2_subdev *sd, 
		input, output);



	/* saa7111/3 does not have these inputs */

	if (state->ident <= V4L2_IDENT_SAA7113 &&

	if ((state->ident <= V4L2_IDENT_SAA7113 ||

	     state->ident == V4L2_IDENT_GM7113C) &&

	    (input == SAA7115_COMPOSITE4 ||

	     input == SAA7115_COMPOSITE5)) {

		return -EINVAL;
@@ -1699,11 +1730,6 @@ static int saa711x_probe(struct i2c_client *client, 
	if (ident < 0)

		return ident;



	if (ident == V4L2_IDENT_GM7113C) {

		v4l_warn(client, "%s not yet supported\n", name);

		return -ENODEV;

	}



	strlcpy(client->name, name, sizeof(client->name));



	state = devm_kzalloc(&client->dev, sizeof(*state), GFP_KERNEL);
@@ -1753,6 +1779,7 @@ static int saa711x_probe(struct i2c_client *client, 
	case V4L2_IDENT_SAA7111A:

		saa711x_writeregs(sd, saa7111_init);

		break;

	case V4L2_IDENT_GM7113C:

	case V4L2_IDENT_SAA7113:

		saa711x_writeregs(sd, saa7113_init);

		break;

CRA Git | Maintained and supported by SUSTech CRA and CCSE