Gitlab 现已全面支持 git over ssh 与 git over https。通过 HTTPS 访问请配置带有 read_repository / write_repository 权限的 Personal access token。通过 SSH 端口访问请使用 22 端口或 13389 端口。如果使用CAS注册了账户但不知道密码，可以自行至设置中更改；如有其他问题，请发邮件至 service@cra.moe 寻求协助。

Commit 0f00a206 authored Oct 13, 2009 by Lalit Chandivade Committed by James Bottomley Dec 04, 2009

[SCSI] qla2xxx: Properly handle UNDERRUN completion statuses.



Correct issues where the lower scsi-status would be improperly
cleared, instead, allow the midlayer to process the status after
the proper residual-count checks are performed.  Finally,
validate firmware status flags prior to assigning values from the
FCP_RSP frame.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Michael Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

parent 531a82d1

drivers/scsi/qla2xxx/qla_isr.c

+57 −63

Original line number	Diff line number	Diff line
		@@ -1353,15 +1353,21 @@ qla2x00_status_entry(scsi_qla_host_t vha, struct rsp_que rsp, void *pkt)

		sense_len = rsp_info_len = resid_len = fw_resid_len = 0;
		if (IS_FWI2_CAPABLE(ha)) {
		if (scsi_status & SS_SENSE_LEN_VALID)
		sense_len = le32_to_cpu(sts24->sense_len);
		if (scsi_status & SS_RESPONSE_INFO_LEN_VALID)
		rsp_info_len = le32_to_cpu(sts24->rsp_data_len);
		if (scsi_status & (SS_RESIDUAL_UNDER \| SS_RESIDUAL_OVER))
		resid_len = le32_to_cpu(sts24->rsp_residual_count);
		if (comp_status == CS_DATA_UNDERRUN)
		fw_resid_len = le32_to_cpu(sts24->residual_len);
		rsp_info = sts24->data;
		sense_data = sts24->data;
		host_to_fcp_swap(sts24->data, sizeof(sts24->data));
		} else {
		if (scsi_status & SS_SENSE_LEN_VALID)
		sense_len = le16_to_cpu(sts->req_sense_length);
		if (scsi_status & SS_RESPONSE_INFO_LEN_VALID)
		rsp_info_len = le16_to_cpu(sts->rsp_info_len);
		resid_len = le32_to_cpu(sts->residual_length);
		rsp_info = sts->rsp_info;
		@@ -1449,38 +1455,62 @@ qla2x00_status_entry(scsi_qla_host_t vha, struct rsp_que rsp, void *pkt)
		break;

		case CS_DATA_UNDERRUN:
		resid = resid_len;
		DEBUG2(printk(KERN_INFO
		"scsi(%ld:%d:%d) UNDERRUN status detected 0x%x-0x%x. "
		"resid=0x%x fw_resid=0x%x cdb=0x%x os_underflow=0x%x\n",
		vha->host_no, cp->device->id, cp->device->lun, comp_status,
		scsi_status, resid_len, fw_resid_len, cp->cmnd[0],
		cp->underflow));

		/* Use F/W calculated residual length. */
		if (IS_FWI2_CAPABLE(ha)) {
		if (!(scsi_status & SS_RESIDUAL_UNDER)) {
		lscsi_status = 0;
		} else if (resid != fw_resid_len) {
		scsi_status &= ~SS_RESIDUAL_UNDER;
		lscsi_status = 0;
		}
		resid = fw_resid_len;
		resid = IS_FWI2_CAPABLE(ha) ? fw_resid_len : resid_len;
		scsi_set_resid(cp, resid);
		if (scsi_status & SS_RESIDUAL_UNDER) {
		if (IS_FWI2_CAPABLE(ha) && fw_resid_len != resid_len) {
		DEBUG2(printk(
		"scsi(%ld:%d:%d:%d) Dropped frame(s) "
		"detected (%x of %x bytes)...residual "
		"length mismatch...retrying command.\n",
		vha->host_no, cp->device->channel,
		cp->device->id, cp->device->lun, resid,
		scsi_bufflen(cp)));

		cp->result = DID_ERROR << 16 \| lscsi_status;
		break;
		}

		if (scsi_status & SS_RESIDUAL_UNDER) {
		scsi_set_resid(cp, resid);
		} else {
		DEBUG2(printk(KERN_INFO
		"scsi(%ld:%d:%d) UNDERRUN status detected "
		"0x%x-0x%x. resid=0x%x fw_resid=0x%x cdb=0x%x "
		"os_underflow=0x%x\n", vha->host_no,
		cp->device->id, cp->device->lun, comp_status,
		scsi_status, resid_len, resid, cp->cmnd[0],
		cp->underflow));
		if (!lscsi_status &&
		((unsigned)(scsi_bufflen(cp) - resid) <
		cp->underflow)) {
		qla_printk(KERN_INFO, ha,
		"scsi(%ld:%d:%d:%d): Mid-layer underflow "
		"detected (%x of %x bytes)...returning "
		"error status.\n", vha->host_no,
		cp->device->channel, cp->device->id,
		cp->device->lun, resid, scsi_bufflen(cp));

		cp->result = DID_ERROR << 16;
		break;
		}
		} else if (!lscsi_status) {
		DEBUG2(printk(
		"scsi(%ld:%d:%d:%d) Dropped frame(s) detected "
		"(%x of %x bytes)...firmware reported underrun..."
		"retrying command.\n", vha->host_no,
		cp->device->channel, cp->device->id,
		cp->device->lun, resid, scsi_bufflen(cp)));

		cp->result = DID_ERROR << 16;
		break;
		}

		cp->result = DID_OK << 16 \| lscsi_status;

		/*
		* Check to see if SCSI Status is non zero. If so report SCSI
		* Status.
		*/
		if (lscsi_status != 0) {
		cp->result = DID_OK << 16 \| lscsi_status;

		if (lscsi_status == SAM_STAT_TASK_SET_FULL) {
		DEBUG2(printk(KERN_INFO
		"scsi(%ld): QUEUE FULL status detected "
		@@ -1507,42 +1537,6 @@ qla2x00_status_entry(scsi_qla_host_t vha, struct rsp_que rsp, void *pkt)
		break;

		qla2x00_handle_sense(sp, sense_data, sense_len, rsp);
		} else {
		/*
		* If RISC reports underrun and target does not report
		* it then we must have a lost frame, so tell upper
		* layer to retry it by reporting an error.
		*/
		if (!(scsi_status & SS_RESIDUAL_UNDER)) {
		DEBUG2(printk("scsi(%ld:%d:%d:%d) Dropped "
		"frame(s) detected (%x of %x bytes)..."
		"retrying command.\n",
		vha->host_no, cp->device->channel,
		cp->device->id, cp->device->lun, resid,
		scsi_bufflen(cp)));

		scsi_set_resid(cp, resid);
		cp->result = DID_ERROR << 16;
		break;
		}

		/* Handle mid-layer underflow */
		if ((unsigned)(scsi_bufflen(cp) - resid) <
		cp->underflow) {
		qla_printk(KERN_INFO, ha,
		"scsi(%ld:%d:%d:%d): Mid-layer underflow "
		"detected (%x of %x bytes)...returning "
		"error status.\n", vha->host_no,
		cp->device->channel, cp->device->id,
		cp->device->lun, resid,
		scsi_bufflen(cp));

		cp->result = DID_ERROR << 16;
		break;
		}

		/* Everybody online, looking good... */
		cp->result = DID_OK << 16;
		}
		break;

CRA Git | Maintained and supported by SUSTech CRA and CCSE