Commit faf912d4 authored by Jordan Yates's avatar Jordan Yates Committed by Benjamin Cabé
Browse files

sensor: tmp108: fix one-shot mode for as6212 

When configuring the device to run in one-shot mode, the AS6212 requires
the sleep mode bit to be set. From the datasheet:

```
The sleep mode is activated by setting the bit SM in the configuration
register to 1. This shuts the device down immediately and reduces the
power consumption to a minimum value.

Entering the sleep mode will take some time (120 ms maximum) and the
first conversion after the sleep mode has been entered takes longer than
the values specified in Figure 7. It is therefore recommended when
entering sleep mode to trigger a single shot conversion at the same
time. After 150 ms (max), the device has then entered the sleep mode and
subsequent conversion times are as specified in Figure 7.
```

Signed-off-by: default avatarJordan Yates <jordan@embeint.com>
parent f5434c13

drivers/sensor/ti/tmp108/tmp108.h

+7 −2
Changes for drivers/sensor/ti/tmp108/tmp108.h: 7 added lines, 2 removed lines.
Original line number Diff line number Diff line
@@ -24,6 +24,7 @@ 
			 .CONF_HYS0 = TI_TMP108_CONF_NA,\

			 .CONF_CR0  = 0x0040,	\

			 .CONF_CR1  = 0x0080,	\

			 .CONF_SLEEP = 0x0100,  \

			 .CONF_M1   = 0x0000,	\

			 .CONF_TM   = 0x0200,	\

			 .CONF_POL  = 0x0400,	\
@@ -47,9 +48,11 @@ 
			 .WAKEUP_TIME_IN_MS = 30 }



#define TI_TMP108_MODE_SHUTDOWN(x) 0

#define TI_TMP108_MODE_ONE_SHOT(x) TI_TMP108_CONF_M0(x)

#define TI_TMP108_MODE_ONE_SHOT(x) (TI_TMP108_CONF_M0(x) | TI_TMP108_CONF_SLEEP(x))

#define TI_TMP108_MODE_CONTINUOUS(x) TI_TMP108_CONF_M1(x)

#define TI_TMP108_MODE_MASK(x)	~(TI_TMP108_CONF_M0(x) | TI_TMP108_CONF_M1(x))

#define TI_TMP108_MODE_MASK(x)	~(TI_TMP108_CONF_M0(x) | \

				  TI_TMP108_CONF_M1(x) | \

				  TI_TMP108_CONF_SLEEP(x))



#define TI_TMP108_FREQ_4_SECS(x) 0

#define TI_TMP108_FREQ_1_HZ(x) TI_TMP108_GET_CONF(x, CONF_CR0)
@@ -77,6 +80,7 @@ 


#define TI_TMP108_CONF_M1(x) TI_TMP108_GET_CONF(x, CONF_M1)

#define TI_TMP108_CONF_M0(x) TI_TMP108_GET_CONF(x, CONF_M0)

#define TI_TMP108_CONF_SLEEP(x) TI_TMP108_GET_CONF(x, CONF_SLEEP)



#define TMP108_TEMP_MULTIPLIER(x)	TI_TMP108_GET_CONF(x, TEMP_MULT)

#define TMP108_TEMP_DIVISOR(x)	TI_TMP108_GET_CONF(x, TEMP_DIV)
@@ -88,6 +92,7 @@ 
struct tmp_108_reg_def {

	uint16_t CONF_M0;	/** Mode 1 configuration bit */

	uint16_t CONF_M1;	/** Mode 2 configuration bit */

	uint16_t CONF_SLEEP;    /** Sleep mode configuration bit */

	uint16_t CONF_CR0;	/** Conversion rate 1 configuration bit */

	uint16_t CONF_CR1;	/** Conversion rate 2 configuration bit */

	uint16_t CONF_POL;	/** Alert pin Polarity configuration bit */

CRA Git | Maintained and supported by SUSTech CRA and CCSE